Miata Turbo Forum - Boost cars, acquire cats.

Miata Turbo Forum - Boost cars, acquire cats. (https://www.miataturbo.net/)
-   Supercharger Discussion (https://www.miataturbo.net/supercharger-discussion-38/)
-   -   JRSC M45 tuning input or advice (https://www.miataturbo.net/supercharger-discussion-38/jrsc-m45-tuning-input-advice-102462/)

domwoppp 03-28-2020 10:51 AM

JRSC M45 tuning input or advice
 
Hello all and thank you for any help given... Need advice or input on what tuning route to go on '90 miata adjustable fuel pressure regulator, 320 cc injectors, 340lph fuel pump, header, 8lb flywheel HD clutch, AFM removal as shown on miatajoe.50megs,com newly rebuilt JRSC with 62.5 pulley have emanage ultimate and boomslang with 3bar pressure sensor not installed yet..and WB Wideband brand AFR and Boost gauges also not installed yet. What else might I install knock sensor etc? Again any input or advice greatly appreciated. Thanks for your time. Nick

Jack Wolfson 04-02-2020 12:27 PM

I have a megasquirt running on my jrsc miata mines aswell a 1990 Stock fuel pump and injectors and clutch innovate wideband runs pretty good I’d suggest get a megasquirt what crank pulley did you buy in having some crank wobble issues knowing it’s a short nose crank in worried might be going turbo

santosspl 05-06-2020 06:50 PM

curious, can you share your megasquirt files?..just need for a baseline? thanks very much

Jack Wolfson 05-06-2020 09:33 PM

Megasquirt tuning
 

Originally Posted by santosspl (Post 1569859)
curious, can you share your megasquirt files?..just need for a baseline? thanks very much

I can help you with tuning your car if you need it give me your phone number I can send u a good tune easily

Jack Wolfson 05-07-2020 01:59 AM


Originally Posted by domwoppp (Post 1565392)
Hello all and thank you for any help given... Need advice or input on what tuning route to go on '90 miata adjustable fuel pressure regulator, 320 cc injectors, 340lph fuel pump, header, 8lb flywheel HD clutch, AFM removal as shown on miatajoe.50megs,com newly rebuilt JRSC with 62.5 pulley have emanage ultimate and boomslang with 3bar pressure sensor not installed yet..and WB Wideband brand AFR and Boost gauges also not installed yet. What else might I install knock sensor etc? Again any input or advice greatly appreciated. Thanks for your time. Nick

I’m assuming you have a intake temp sensor so you want to run on fuel density there is a lot more to it than what I can tell you but if u are running megasquirt I’d get a exhaust gas temp sensor if you want to make sure it’s running safe that’s an easy way to tell .you have plenty fuel it should run good You will have troubles idling it’s hard with the supercharger and that long tube they sue if you get rid of the valve in that tube and make it short right into the charge pipe it should work better and at 8lbs might want to think about a intercooler soon but for now run safe timing

Gkaz 11-14-2020 03:12 PM

So you have a JRSC with basically stock everything else? I just got a megasquirt and I believe we have the same setup. Would you be able to send your files so I could understand what I'm doing a little more?

HowPrayGame 11-14-2020 03:53 PM

Do you have upgraded injectors? You will want upgraded injectors for an M45 with a JRSC, FF640CC injectors are great for running sequential injection


All times are GMT -4. The time now is 02:02 AM.


© 2024 MH Sub I, LLC dba Internet Brands