Help :/ TWO Broken 6-Speeds in 1000 miles (Weird Problem)
#22
Moderator
iTrader: (12)
Join Date: Nov 2008
Location: Tampa, Florida
Posts: 20,652
Total Cats: 3,011
I was pretty sure everybody in the world knew that you did Dyno pulls in 5th gear with a Miata 6-speed, fwiw. By the way, your horsepower and torque numbers being reported may be different than actual because you were using a lower gear on the dyno.
#23
Junior Member
iTrader: (1)
Join Date: Oct 2015
Location: Metro Detroit, MI
Posts: 397
Total Cats: 36
Saw this thread and wondered it is was our boi @ TCPC :( It was indeed.
I don't think it sounds like a clutch problem, but idk. Do you have a spare 5 spd to throw in? Maybe that will help identify the problem if you use the same clutch setup. As others said it could be the shifter, but the fact that the first failure occurred while during cruise kind of throws that out the window.
PM me if you need a 5 spd. I can send one out today, just pay shipping.
I don't think it sounds like a clutch problem, but idk. Do you have a spare 5 spd to throw in? Maybe that will help identify the problem if you use the same clutch setup. As others said it could be the shifter, but the fact that the first failure occurred while during cruise kind of throws that out the window.
PM me if you need a 5 spd. I can send one out today, just pay shipping.
Last edited by Goingnowherefast; 12-28-2017 at 12:45 PM.
#24
TheCarPassionChannel
Thread Starter
Join Date: Mar 2013
Location: San Diego, Ca
Posts: 188
Total Cats: 136
1st trans unknown, but purchased from a personal friend and it was working fine when pulled. 2nd trans 102k. Clutch/flywheel 1400 miles.
Honestly man, you are wasting your time with this thread
It doesnt matter why they are breaking, wjether its something in the shift linkage, clutch, transmission... Becausr you are at a torque and power level that easily breaks the miata 6 speed.
Even if you fix the current issue, you WILL have a torque related failure with the next miata 6 speed, within a few months, if you actually drive the thing.
Get the k miata setup, it replaces the linkages too.
It doesnt matter why they are breaking, wjether its something in the shift linkage, clutch, transmission... Becausr you are at a torque and power level that easily breaks the miata 6 speed.
Even if you fix the current issue, you WILL have a torque related failure with the next miata 6 speed, within a few months, if you actually drive the thing.
Get the k miata setup, it replaces the linkages too.
#25
There are two things in common between the two failures. Flywheel/clutch ane the MR shifter. From the symptoms, I agree we can rule the clutch/flywheel out and I know you checked the endplay on the crank (I watch the videos as they come out. Waiting for the junkyard to pull my VVT so I can dump it in my 90!).
This leaves the MR short shifter. The fact you are saying it is sticky moving between gears while sitting on the second one tells me something is up with the gear shifting mechanism. It takes 5min to swap in a stock shifter if you have one. Do that and report back so we can at least eleminate that as a variable.
This leaves the MR short shifter. The fact you are saying it is sticky moving between gears while sitting on the second one tells me something is up with the gear shifting mechanism. It takes 5min to swap in a stock shifter if you have one. Do that and report back so we can at least eleminate that as a variable.
#26
TheCarPassionChannel
Thread Starter
Join Date: Mar 2013
Location: San Diego, Ca
Posts: 188
Total Cats: 136
This leaves the MR short shifter. The fact you are saying it is sticky moving between gears while sitting on the second one tells me something is up with the gear shifting mechanism. It takes 5min to swap in a stock shifter if you have one. Do that and report back so we can at least eleminate that as a variable.
#27
My guess is it's related to your clutch/flywheel in some way. Spacing is off, balance is off, something is loading the input shaft in a way it shouldn't be. Is the sheet metal spacer thingy that goes between the engine and trans installed? If you have a stock clutch/stock flywheel, perhaps check a few dimensions to verify the new clutch is spacing the disk in the same spot on the input shaft as a stock clutch.
#28
Former Vendor
iTrader: (31)
Join Date: Nov 2006
Location: Sunnyvale, CA
Posts: 15,442
Total Cats: 2,099
My thought process:
- Two identical, uncommon failures means it's likely an external force acting on the gearbox. There are not many of those (pilot bearing, clutch, shifter, driveshaft, ?)
- Hi-power 6sp failure mode is a gear failure, you don't have a gear failure (verified by visual inspection) so we can set that aside for now
- Driveshaft is OEM, we can rule that out
- Hundreds of people using MR shifters in 6speeds, this is not a common failure, so we can rule that out
- Clutch is an uncommon twin-disc that I've actually never heard of before, so.... ???
#29
I'm surprised some people are acting like a 6 speed can't reliably handle ~300hp on a street driven miata. I've got probably 80k miles on high mileage NB1 6 speeds over 300hp and I've only killed one after a whole lot of abuse.
#30
To clarify, do you have any mileage with this particular clutch on another transmission where it didn't fail, or was this clutch installed along with the 6sp during your 1.8L build?
My thought process:
My thought process:
- Two identical, uncommon failures means it's likely an external force acting on the gearbox. There are not many of those (pilot bearing, clutch, shifter, driveshaft, ?)
- Hi-power 6sp failure mode is a gear failure, you don't have a gear failure (verified by visual inspection) so we can set that aside for now
- Driveshaft is OEM, we can rule that out
- Hundreds of people using MR shifters in 6speeds, this is not a common failure, so we can rule that out
- Clutch is an uncommon twin-disc that I've actually never heard of before, so.... ???
#33
Elite Member
iTrader: (15)
Join Date: Jan 2007
Location: Murfreesboro,TN
Posts: 2,043
Total Cats: 265
To clarify, do you have any mileage with this particular clutch on another transmission where it didn't fail, or was this clutch installed along with the 6sp during your 1.8L build?
My thought process:
My thought process:
- Two identical, uncommon failures means it's likely an external force acting on the gearbox. There are not many of those (pilot bearing, clutch, shifter, driveshaft, ?)
- Hi-power 6sp failure mode is a gear failure, you don't have a gear failure (verified by visual inspection) so we can set that aside for now
- Driveshaft is OEM, we can rule that out
- Hundreds of people using MR shifters in 6speeds, this is not a common failure, so we can rule that out
- Clutch is an uncommon twin-disc that I've actually never heard of before, so.... ???
#34
TheCarPassionChannel
Thread Starter
Join Date: Mar 2013
Location: San Diego, Ca
Posts: 188
Total Cats: 136
To clarify, do you have any mileage with this particular clutch on another transmission where it didn't fail, or was this clutch installed along with the 6sp during your 1.8L build?
My thought process:
My thought process:
- Two identical, uncommon failures means it's likely an external force acting on the gearbox. There are not many of those (pilot bearing, clutch, shifter, driveshaft, ?)
- Hi-power 6sp failure mode is a gear failure, you don't have a gear failure (verified by visual inspection) so we can set that aside for now
- Driveshaft is OEM, we can rule that out
- Hundreds of people using MR shifters in 6speeds, this is not a common failure, so we can rule that out
- Clutch is an uncommon twin-disc that I've actually never heard of before, so.... ???
With the clutch pedal out, it wouldn't matter if the TOB was seized. And it's not because I just had it all apart and check it.
These are both irrelevant while the clutch is out though.
Last edited by 1993z32; 12-28-2017 at 01:18 PM.
#35
There are documented failures of 250wtq track work killing 6 speeds.
Most of the "300-350whp street cars running for a long time" is not a good data point, because they dont actually drive with that setting. Ive never been in a community like this that knowingly builds for decent power, then turns it way down like a bitch.
You are running 350wtq, i fail to comprehend why you are trying to make a 6 speed that is basically designed to have its shafts pushed apart under 300wtq, work.
Most of the "300-350whp street cars running for a long time" is not a good data point, because they dont actually drive with that setting. Ive never been in a community like this that knowingly builds for decent power, then turns it way down like a bitch.
You are running 350wtq, i fail to comprehend why you are trying to make a 6 speed that is basically designed to have its shafts pushed apart under 300wtq, work.
#36
There are documented failures of 250wtq track work killing 6 speeds.
Most of the "300-350whp street cars running for a long time" is not a good data point, because they dont actually drive with that setting. Ive never been in a community like this that knowingly builds for decent power, then turns it way down like a bitch.
You are running 350wtq, i fail to comprehend why you are trying to make a 6 speed that is basically designed to have its shafts pushed apart under 300wtq, work.
Most of the "300-350whp street cars running for a long time" is not a good data point, because they dont actually drive with that setting. Ive never been in a community like this that knowingly builds for decent power, then turns it way down like a bitch.
You are running 350wtq, i fail to comprehend why you are trying to make a 6 speed that is basically designed to have its shafts pushed apart under 300wtq, work.
#39
This can be pure FUD, but there is another thing in common with the two failures. I assume it's the same mechanic?
Regarding alignment i have always wondered about my own ignorance about the alignment between the trans and the PPF, I just slap it together in whatever angle the engine/diff mounts make sit possible and torque it down,
I have no clue about if/why/how the prop shaft can make any effect on the possibility to get syncros mangled up och pressurized, just though i'd throw in another question mark to get straightened out.
Have you been able to find pictures on shift forks (bent and ok) to see if yours are truley ok (the pictures in the transmission manual only focus on wear and clearances, not straightness)?
Could it be the "shift rods" where the forks sit, making neutral pressing either forward or rearward (on one or all forks depending on what's being misaligned)?
The whole shifter assembly from a 6sp with stripped 4th gear might be the spare part you are looking for?
Maybe the MR shifter promotes shifting abuse in some way, I know I love mine.
Regarding alignment i have always wondered about my own ignorance about the alignment between the trans and the PPF, I just slap it together in whatever angle the engine/diff mounts make sit possible and torque it down,
I have no clue about if/why/how the prop shaft can make any effect on the possibility to get syncros mangled up och pressurized, just though i'd throw in another question mark to get straightened out.
Have you been able to find pictures on shift forks (bent and ok) to see if yours are truley ok (the pictures in the transmission manual only focus on wear and clearances, not straightness)?
Could it be the "shift rods" where the forks sit, making neutral pressing either forward or rearward (on one or all forks depending on what's being misaligned)?
The whole shifter assembly from a 6sp with stripped 4th gear might be the spare part you are looking for?
Maybe the MR shifter promotes shifting abuse in some way, I know I love mine.
#40
TheCarPassionChannel
Thread Starter
Join Date: Mar 2013
Location: San Diego, Ca
Posts: 188
Total Cats: 136
This can be pure FUD, but there is another thing in common with the two failures. I assume it's the same mechanic?
Regarding alignment i have always wondered about my own ignorance about the alignment between the trans and the PPF, I just slap it together in whatever angle the engine/diff mounts make sit possible and torque it down,
I have no clue about if/why/how the prop shaft can make any effect on the possibility to get syncros mangled up och pressurized, just though i'd throw in another question mark to get straightened out.
This was brought up by a couple people as well, I suppose it's possible, I'm just trying to understand why. I feel more confident in diagnosing now that I have a really good understanding of how everything lines up/works in the trans.
Maybe the MR shifter promotes shifting abuse in some way, I know I love mine.
This is exactly why I babied the 2nd trans. I figured I bent a part of the gear selection mechanisms on the first one.
Regarding alignment i have always wondered about my own ignorance about the alignment between the trans and the PPF, I just slap it together in whatever angle the engine/diff mounts make sit possible and torque it down,
I have no clue about if/why/how the prop shaft can make any effect on the possibility to get syncros mangled up och pressurized, just though i'd throw in another question mark to get straightened out.
This was brought up by a couple people as well, I suppose it's possible, I'm just trying to understand why. I feel more confident in diagnosing now that I have a really good understanding of how everything lines up/works in the trans.
Maybe the MR shifter promotes shifting abuse in some way, I know I love mine.
This is exactly why I babied the 2nd trans. I figured I bent a part of the gear selection mechanisms on the first one.