Originally Posted by Track
(Post 1077322)
I built my own cold air intake using parts from here, for less then $80 bucks I think. That's with a few repeat orders to put the finishing touches on it. It goes into the bumper and grabs ambient air (not coldside air, although I did that for a while also).
I decided to join the cool kids and bought a '95 that already had a lot of worthwhile mods to dedicate to my track endeavors. Right now it has a Jackson Racing intake on it. That's supposed to be a good intake for low temps, but it is definitely on the short size vis-a-vis tuned length. It also forces the air through a bunch of turns. And, frankly, it makes some maintenance tasks a chore and just doesn't look "race-spec." Planning to build up some experimental intakes using SiliconeIntake parts and doing a VD comparison. Would like to see how you're pulling from the bumper. |
23" u bend cold side intake, $50 tops with filter, go read Emilio's E85 138whp? Thread
|
Originally Posted by jacob300zx
(Post 1077460)
23" u bend cold side intake, $50 tops with filter, go read Emilio's E85 138whp? Thread
|
10 Attachment(s)
Originally Posted by jacob300zx
(Post 1077460)
23" u bend cold side intake, $50 tops with filter, go read Emilio's E85 138whp? Thread
EDIT: Dug the thread up, around the dyno post.
Originally Posted by hornetball
(Post 1077423)
Pictures?
I decided to join the cool kids and bought a '95 that already had a lot of worthwhile mods to dedicate to my track endeavors. Right now it has a Jackson Racing intake on it. That's supposed to be a good intake for low temps, but it is definitely on the short size vis-a-vis tuned length. It also forces the air through a bunch of turns. And, frankly, it makes some maintenance tasks a chore and just doesn't look "race-spec." Planning to build up some experimental intakes using SiliconeIntake parts and doing a VD comparison. Would like to see how you're pulling from the bumper. Test Fit https://www.miataturbo.net/attachmen...ine=1385579457 Throttle body -> 90* elbow -> MAF -> aluminum tube -> 90* elbow -> short aluminum tube -> filter. Drill a hole post MAF for the IAT. delete the MAF and use a longer aluminum tube if you have a MS3 and only use an IAT sensor. https://www.miataturbo.net/attachmen...ine=1385579457 Passenger side wheel, comes out of the belly pan and into the wheel cover area. I put two pieces of duct tape together and attached them to the wheel well liner to prevent rocks and stuff from getting kicked into the intake. https://www.miataturbo.net/attachmen...ine=1385579457 Here is the view from the fog light hole. https://www.miataturbo.net/attachmen...ine=1385579457 Here is a view from inside the fog light hole. Note the metal brace I am using to support the intake. It attaches to the same bolt that the belly pan goes to. https://www.miataturbo.net/attachmen...ine=1385579457 |
That's neat, kinda like the AEM intake my friend had on his Integra. He parked the car in an extra low ditch filled with water and hydrolocked the motor. Just a warning, because sometimes NOTRACECAR.
I'd still rock that for trackdays :party: |
Cool (pun intended). Very straightforward.
|
Originally Posted by EO2K
(Post 1077531)
That's neat, kinda like the AEM intake my friend had on his Integra. He parked the car in an extra low ditch filled with water and hydrolocked the motor. Just a warning, because sometimes NOTRACECAR.
I'd still rock that for trackdays :party: Your friend's experience is just...silly. I am not sure if he is stupid, or this was one deceptive ditch...Rest assured, my car doesn't get started in any ditches. While my car is a track only car now, I did daily this intake for the past 2-ish years. I have driven through some heavy rains without problem. At least, I haven't noticed anything. I guess time will tell if I end up with bent valves or some such. |
All times are GMT -4. The time now is 12:47 AM. |
© 2024 MH Sub I, LLC dba Internet Brands