Aidan's loose oily bunghole actually runs a track lap
#4561
Elite Member
iTrader: (37)
Join Date: Apr 2010
Location: Very NorCal
Posts: 10,441
Total Cats: 1,899
Cool. I take it you are piping this into the MS3? I need to figure out how to do this, I'd love to be able to log oil temps, and set a rev limit for low oil temp.
M-Tuned Reroute 1.8 Master Race here, I have a pre thermostat 1/8" NPT port for a sender, I just need a gauge that does not suck.
Or a sender that does not suck. Or whatever. **** just needs to work because I'm tired of ******* with it.
Or a sender that does not suck. Or whatever. **** just needs to work because I'm tired of ******* with it.
#4563
SADFab Destructive Testing Engineer
Thread Starter
iTrader: (5)
Join Date: Apr 2014
Location: Beaverton, USA
Posts: 18,642
Total Cats: 1,866
Then going to try and setup a warning light and a failsafe. Need to set the revlimiter to 0 and see what happens though.
Oh and will be using this: http://jbperf.com/io_extender/tinyIOx.html to connect everything.
#4566
SADFab Destructive Testing Engineer
Thread Starter
iTrader: (5)
Join Date: Apr 2014
Location: Beaverton, USA
Posts: 18,642
Total Cats: 1,866
Megasquirt Support Forum (MSEXTRA) ? Oil Temp Genaric Input & Rev limit (View topic)
Pretty ridiculous way to do it. But might be necessary.
Westfield is a boss.
Pretty ridiculous way to do it. But might be necessary.
Westfield is a boss.
#4570
I'll grab some feeler gauges tomorrow and see if my calipers are centered. If they are I'm not sure what to do, other than run the washers or make brackets with the right offset, hope they're just special for you when it comes to Rallas and Sean...
you could measure the rotor if you want, you'll need to lay a straightedge or something across it and comp the difference with the caliper, if that makes any sense. It should be this..
you could measure the rotor if you want, you'll need to lay a straightedge or something across it and comp the difference with the caliper, if that makes any sense. It should be this..
#4575
Elite Member
iTrader: (37)
Join Date: Apr 2010
Location: Very NorCal
Posts: 10,441
Total Cats: 1,899
Yes. Along with pressure. And probably fuel pressure. And hopefully EGT. And knock. Etc.
Then going to try and setup a warning light and a failsafe. Need to set the revlimiter to 0 and see what happens though.
Oh and will be using this: TinyIOx v1.0 Board to connect everything.
Then going to try and setup a warning light and a failsafe. Need to set the revlimiter to 0 and see what happens though.
Oh and will be using this: TinyIOx v1.0 Board to connect everything.
#4577
Megasquirt Support Forum (MSEXTRA) ? Oil Temp Genaric Input & Rev limit (View topic)
Pretty ridiculous way to do it. But might be necessary.
Pretty ridiculous way to do it. But might be necessary.
--Ian
#4579
Re-merging your changes isn't even all that hard if you use a simple revision control system. Check in the base code, pull a branch for your changes, check them back in. When the new release comes out, you check that into the mainline, then merge it down to your branch.
Back in my undergrad days, I never understood the value to source code control, even in the classes where they tried to get us to use it. A few years later I was taking some grad classes at Stanford (was thinking about getting a master's part time) and the first thing I did when working on a programming assignment was to create a CVS repository.
--Ian
#4580
SADFab Destructive Testing Engineer
Thread Starter
iTrader: (5)
Join Date: Apr 2014
Location: Beaverton, USA
Posts: 18,642
Total Cats: 1,866
If you were talking about major surgery I'd agree, but a simple check to see if pressure/temperature are over some critical threshold is trivial, you just insert a single function call into the main loop. That's way better than some external hackery.
Re-merging your changes isn't even all that hard if you use a simple revision control system. Check in the base code, pull a branch for your changes, check them back in. When the new release comes out, you check that into the mainline, then merge it down to your branch.
Back in my undergrad days, I never understood the value to source code control, even in the classes where they tried to get us to use it. A few years later I was taking some grad classes at Stanford (was thinking about getting a master's part time) and the first thing I did when working on a programming assignment was to create a CVS repository.
--Ian
Re-merging your changes isn't even all that hard if you use a simple revision control system. Check in the base code, pull a branch for your changes, check them back in. When the new release comes out, you check that into the mainline, then merge it down to your branch.
Back in my undergrad days, I never understood the value to source code control, even in the classes where they tried to get us to use it. A few years later I was taking some grad classes at Stanford (was thinking about getting a master's part time) and the first thing I did when working on a programming assignment was to create a CVS repository.
--Ian
Have you messed with the code? Getting the build chain set up is the most annoying/time consuming. I'll look into it at some point.