stroker crank?
#1
stroker crank?
hey does anyone know a good place to get a stroker crank, to make the 1.8 into a 2.0? is there a crank from another "B" engine that will fit but has a longer throw? the only place i've seen one is on flying miata, and they want like 3.5k for the rods, pistons, and crank. just wondering if there were any other options.
on another note, how come people lower the compression of their engines when building a turbo motor? i would think that you would want high compression to make more power, and be able to use a smaller turbo so it spools up sooner. but it seems that everyone in the industry builds a low compression engine for turboing. Theres probably something really simple that i'm missing here but i can't really figure it out.
on another note, how come people lower the compression of their engines when building a turbo motor? i would think that you would want high compression to make more power, and be able to use a smaller turbo so it spools up sooner. but it seems that everyone in the industry builds a low compression engine for turboing. Theres probably something really simple that i'm missing here but i can't really figure it out.
#2
Junior Member
iTrader: (1)
Join Date: Oct 2004
Location: Haarlem ,the Netherlands
Posts: 453
Total Cats: 0
Lower compression prevents detonation...
@ 15psi you add 2x as much air and fuel into the chamber... Don't you guess that it should be lower??
As for stroker cranks... Racing mazda has some too... not as nice as the FM's...
@ 15psi you add 2x as much air and fuel into the chamber... Don't you guess that it should be lower??
As for stroker cranks... Racing mazda has some too... not as nice as the FM's...
#3
2 Props,3 Dildos,& 1 Cat
iTrader: (8)
Join Date: Jun 2005
Location: Fake Virginia
Posts: 19,338
Total Cats: 573
Flyin Miata
Replika Maschinen
as for compression, the trade off for dropping compression is generally always favorable because the amount of boost you can add increases power way more than the loss of compression.
Replika Maschinen
as for compression, the trade off for dropping compression is generally always favorable because the amount of boost you can add increases power way more than the loss of compression.
#4
that just doesn't make sense to me. greddymx5 i'm talking like say i wanna make 350hp. if i had a high compression engine i wouldn't need to have 15psi to reach my hp goal.
Y8s- isn't adding a turbo effectively increasing compression anyways? if detionation is your limit how can you run more boost by lowering the compression and end up with more hp?
thanks for the links the the other sites. still wondering though if you could swap in like a "B20" crank into the 1.8 miata motor.
Y8s- isn't adding a turbo effectively increasing compression anyways? if detionation is your limit how can you run more boost by lowering the compression and end up with more hp?
thanks for the links the the other sites. still wondering though if you could swap in like a "B20" crank into the 1.8 miata motor.
#5
Former Vendor
iTrader: (31)
Join Date: Nov 2006
Location: Sunnyvale, CA
Posts: 15,442
Total Cats: 2,100
No matter how hard you compress 6psi from a turbo, you still only have 6psi worth of oxygen to burn. Drop the compression down a little bit and get to 12 or 15 or 18psi and you have 2-3x the oxygen to burn even if you aren't squeezing it quite as hard. Less compression and more boost is the way to get power.
If you could swap a B-series crank into the Miata, FM wouldn't have gone through the trouble to have their cranks custom-made.
If you could swap a B-series crank into the Miata, FM wouldn't have gone through the trouble to have their cranks custom-made.
#6
Supporting Vendor
iTrader: (33)
Join Date: Jul 2006
Location: atlanta-ish
Posts: 12,659
Total Cats: 134
No matter how hard you compress 6psi from a turbo, you still only have 6psi worth of oxygen to burn. Drop the compression down a little bit and get to 12 or 15 or 18psi and you have 2-3x the oxygen to burn even if you aren't squeezing it quite as hard. Less compression and more boost is the way to get power.
Higher compression is always better for power and response.
Lower compression is easier to tune and can run on lower octane fuel.
Trade offs.
A well tuned high compression motor will pull away from a well tuned low compression motor. Assuming both are properly fueled.
#7
Former Vendor
iTrader: (31)
Join Date: Nov 2006
Location: Sunnyvale, CA
Posts: 15,442
Total Cats: 2,100
I was talking straight out of my ***, but I still don't believe that higher compression is always better. Take superchargers for E46 M3s, for instance. AA and Dinan both keep stock compression, but EVOsport drops it down and makes like 100 more hp.
#8
Supporting Vendor
iTrader: (33)
Join Date: Jul 2006
Location: atlanta-ish
Posts: 12,659
Total Cats: 134
No arguement
I don't know the first thing about blowing a BMW, but there is more going on than EVO lowering compression to make more power. All other things equal, lower compression means LESS power.
but I still don't believe that higher compression is always better. Take superchargers for E46 M3s, for instance. AA and Dinan both keep stock compression, but EVOsport drops it down and makes like 100 more hp.
#10
Ben- you said that you can use lower octane fuel. Thats why probably most people run a lower compression engine. how low do you think you can go? how much power can someone running 8:1 CR or 9:1 make? wouldn't lower compression me you could run less timing advance also? if that is the case how come people don't make 7:1 or 6:1 compression ratios? logically if you did that (destroked the engine) wouldn't you be able to run like 12psi without too much timing advance on pump gas? talkin theortically here now...
sucks about the crank, could you imagine how fun it would be to have a cheap 2.0 miata engine?
sucks about the crank, could you imagine how fun it would be to have a cheap 2.0 miata engine?
#11
Ben- you said that you can use lower octane fuel. Thats why probably most people run a lower compression engine. how low do you think you can go? how much power can someone running 8:1 CR or 9:1 make? wouldn't lower compression me you could run less timing advance also? if that is the case how come people don't make 7:1 or 6:1 compression ratios? logically if you did that (destroked the engine) wouldn't you be able to run like 12psi without too much timing advance on pump gas? talkin theortically here now...
sucks about the crank, could you imagine how fun it would be to have a cheap 2.0 miata engine?
sucks about the crank, could you imagine how fun it would be to have a cheap 2.0 miata engine?
#12
Former Vendor
iTrader: (31)
Join Date: Nov 2006
Location: Sunnyvale, CA
Posts: 15,442
Total Cats: 2,100
No argument that less compression = less power, but EVOsport is able to CRANK the boost when they dump the compression. Can you explain theoretically why it is better to compress less air harder vs. compressing more air more softly?
#15
For some reason I remember that the flame propogation gets affected with higher compression because you are affecting the quench point for the cylinder. This has many advantages, but can be really bad when you start to add boost into the mix. Don't quote me, but I think that it has something to do with this.