Fluid leak from lines at brake master cylinder
#1
Elite Member
Thread Starter
iTrader: (4)
Join Date: Aug 2009
Location: Redwood City, CA
Posts: 1,784
Total Cats: 42
Fluid leak from lines at brake master cylinder
Replaced master cylinder. Had a friend step on the pedal. A tiny bit of fluid is leaking past the threads. Tightened them as far as I dare and theres still some seeping when he holds the pedal down. Anyone recommend anything I can put on the threads to seal it? I've heard teflon tape is bad for this kind of thing, so I didn't try, but has anyone actually tried it?
I did a search but didn't really find anything on this. Gotta get this thing driving by sunset, so any help is appreciated.
EDIT: Tightened it to about 9999.5 ft/lbs and leak stopped. Fail. Literally put all my weight on the wrench. Surprised it didn't break.
I did a search but didn't really find anything on this. Gotta get this thing driving by sunset, so any help is appreciated.
EDIT: Tightened it to about 9999.5 ft/lbs and leak stopped. Fail. Literally put all my weight on the wrench. Surprised it didn't break.
Last edited by MartinezA92; 06-29-2010 at 08:15 PM.
#2
Senior Member
iTrader: (4)
Join Date: Jan 2008
Location: Falls Church, VA
Posts: 1,361
Total Cats: 17
So those were the original flare fittings you were cranking down on? Those are steel, yes? I can tell you from experience that if you do that with brass, the fitting will split or shear off. I did that with one of the FM fittings that came with my prop valve. It was leaking so I just cranked it down trying to get it to seal, until it snapped.
The replacement got some thread sealer. I used white teflon paste. Wilwood supplies their brass fittings pre-coated with some sort of red thread locker, not sure if it's exactly identical to red Loctite or not. Anyway, the teflon paste worked fine for me. I installed the prop valve about 8-9 months ago, done 5 track days in that time and have had zero leaks, and I do watch it like a hawk for any evidence of fluid seeping past the threads.
The replacement got some thread sealer. I used white teflon paste. Wilwood supplies their brass fittings pre-coated with some sort of red thread locker, not sure if it's exactly identical to red Loctite or not. Anyway, the teflon paste worked fine for me. I installed the prop valve about 8-9 months ago, done 5 track days in that time and have had zero leaks, and I do watch it like a hawk for any evidence of fluid seeping past the threads.
#4
Elite Member
iTrader: (1)
Join Date: Feb 2008
Location: Birmingham Alabama
Posts: 7,930
Total Cats: 45
Brave one leaning on the wrench. A flare fitting should never need to be tightened like that and frankly, in my opinion should not be, if everything is correct. Either the flare or the nut is boogered. I don't like using sealants on stuff like that, that should not require it. That would be a bandaid.
#6
Elite Member
iTrader: (1)
Join Date: Feb 2008
Location: Birmingham Alabama
Posts: 7,930
Total Cats: 45
Only fix I would trust now after having muscled it that hard, would be to rent a flare tool, get a new flare nut, and cut the existing flare off and redo it, bend tubing as needed to make it work. But I'm ---- like that.
#9
Be meticulous about dirt not getting into things (and don't trust the guys who built the master cylinder that it's clean), and be careful taking things apart and you won't have an issue 99% of the time.
#13
Elite Member
iTrader: (21)
Join Date: Jun 2007
Location: Rochester, NY
Posts: 6,597
Total Cats: 1,263
If you think that part is fine, I suggest checking the flare. Probably split. Cut it off, and re-flare as suggested above. If in doubt, buy another line. Brakes are one place you can't tolerate anything less than right.
#14
Elite Member
Thread Starter
iTrader: (4)
Join Date: Aug 2009
Location: Redwood City, CA
Posts: 1,784
Total Cats: 42
The master came with a bag of plastic threaded plugs, for bench bleeding. I don't know how I didn't notice it before, but the plug doesn't go in straight to the threaded hole in question. It looks like the threads in the hole aren't straight. The flare nut LOOKS crossthreaded, but really isn't.
Fuuuuuuuuuuuuuuuuuuuuuuuu
No leaks though.
Fuuuuuuuuuuuuuuuuuuuuuuuu
No leaks though.
Thread
Thread Starter
Forum
Replies
Last Post