New Firmware/Software! - Miata Turbo Forum - Boost cars, acquire cats.

Welcome to Miataturbo.net   Members
 


Reply
 
 
 
LinkBack Thread Tools Search this Thread
Old 08-03-2009, 07:45 AM   #1
Elite Member
Thread Starter
iTrader: (9)
 
Join Date: Jun 2008
Location: Houston, TX
Posts: 1,583
Total Cats: 8
Default New Firmware/Software!

Adaptronic Firmware (V1.0P)

New Firmware Link

This is the latest firmware for the Adaptronic e420c ECU. It is suitable for version 1.0 of the hardware. Right click, select "Save As...", and install it to the ECU using FlashItV1.

Adaptronic_V10P.adf - requires WARI Version 1.12
Earlier versions & revision history

V1.0P (2009-Aug-03) - WARI Version V1.12

* Corrected tacho on aux output for 50% duty cycle
* Added transient throttle ignition advance
* Added logic-only inputs based on logic-only outputs
* Added boost duty cycle scaling based on percent TPS
* Removed 'Enable Datalogging' input feature
* Added aux output based on battery voltage
* Improved MAP and TPS resolution, now 1/16 of a kPa or Percent for interpolation
* Removed MAP filter
* Corrected bug with the closed-loop fuel max TPS
* Added 2-rotor wasted leading, alternate/DF trailing mode
* Added 2-rotor direct fire mode
* Added ELM327 Scantool error correct mode @ 38400 baud
* Added new tuning mode: 1=MAP, 2=MAP, Pri = 1, Sec = 1x2, Ign = 1
* also added injector 3/4 trim (rear rotor trim), when in this tuning mode
* Fixed bug with max RPM and max Load for closed-loop fuel control
* Added min load for closed-loop fuel control
* Fixed bug with WOT enrichment
* Added special trigger mode for Nissan VQ30 engine
* Added AEM UEGO 0-5V on spare input
* Added protocol for Innovate TC-4 thermocouple interface device, on second serial port
* Added support for Gen 5 Suzuki Swift triggering, with VVT and sequential injection
* Improved accuracy of VVT angle detection
* Added option for idle-up on each close throttle event (dashpot)
* Fixed bug in TPS cutoff for asynch accelerator pump

Last edited by TravisR; 08-03-2009 at 08:00 AM.
TravisR is offline   Reply With Quote
Old 08-03-2009, 07:55 AM   #2
Murderator
iTrader: (76)
 
18psi's Avatar
 
Join Date: Apr 2008
Posts: 36,206
Total Cats: 2,587
Default

This is the newest/greatest? NICE
I don't see a link to it though.
18psi is offline   Reply With Quote
Old 08-03-2009, 10:45 AM   #3
y8s
2 Props,3 Dildos,& 1 Cat
iTrader: (8)
 
y8s's Avatar
 
Join Date: Jun 2005
Location: Fake Virginia
Posts: 19,038
Total Cats: 407
Default

Quote:
Originally Posted by TravisR View Post
Adaptronic Firmware (V1.0P)

* Fixed bug in TPS cutoff for asynch accelerator pump

WAT


there's a bug?
y8s is offline   Reply With Quote
Old 08-03-2009, 10:53 AM   #4
Elite Member
Thread Starter
iTrader: (9)
 
Join Date: Jun 2008
Location: Houston, TX
Posts: 1,583
Total Cats: 8
Default

I know I seen that!! I don't know what its referring to.
TravisR is offline   Reply With Quote
Old 08-03-2009, 10:54 AM   #5
Elite Member
iTrader: (46)
 
Stein's Avatar
 
Join Date: Dec 2007
Location: Nebraska
Posts: 4,812
Total Cats: 138
Default

Damn, too late. I wanted to ask them on their next release if they can put a user selectable setting to toggle between *C and *F. Should be easy and some of us have a hard time converting celcius in our heads.
Stein is offline   Reply With Quote
Old 08-03-2009, 10:57 AM   #6
Elite Member
iTrader: (46)
 
Stein's Avatar
 
Join Date: Dec 2007
Location: Nebraska
Posts: 4,812
Total Cats: 138
Default

Quote:
Originally Posted by TravisR View Post
I know I seen that!! I don't know what its referring to.
Maybe it will fix my 0>1% TPS lean tip in.
Stein is offline   Reply With Quote
Old 08-03-2009, 10:59 AM   #7
Elite Member
Thread Starter
iTrader: (9)
 
Join Date: Jun 2008
Location: Houston, TX
Posts: 1,583
Total Cats: 8
Default

I'm not really good at the convert either, but I know water boils at a 100, and room temperature is about 20-25. If anything is just acting weird I could spot it by that. Considering these guys mostly serve software to the domesticated world, I doubt we get any help because we still use the kings foot to measure distance.
TravisR is offline   Reply With Quote
Old 08-03-2009, 01:37 PM   #8
Murderator
iTrader: (76)
 
18psi's Avatar
 
Join Date: Apr 2008
Posts: 36,206
Total Cats: 2,587
Default

Excellent.
18psi is offline   Reply With Quote
Old 08-03-2009, 01:47 PM   #9
y8s
2 Props,3 Dildos,& 1 Cat
iTrader: (8)
 
y8s's Avatar
 
Join Date: Jun 2005
Location: Fake Virginia
Posts: 19,038
Total Cats: 407
Default

Quote:
Originally Posted by TravisR View Post
I'm not really good at the convert either, but I know water boils at a 100, and room temperature is about 20-25. If anything is just acting weird I could spot it by that. Considering these guys mostly serve software to the domesticated world, I doubt we get any help because we still use the kings foot to measure distance.
stupid farenheit. 100 is "about body temperature"? 0 is the temperature of some icewater with ammonium chloride in it? what? why?
y8s is offline   Reply With Quote
Old 08-03-2009, 03:34 PM   #10
Elite Member
iTrader: (15)
 
Join Date: Dec 2007
Location: San Antonio, Texas
Posts: 4,889
Total Cats: 28
Default

Quote:
Originally Posted by TravisR View Post
Adaptronic Firmware (V1.0P)

* Added logic-only inputs based on logic-only outputs
Nice. If that is what I think it is, I will be using that feature.
ZX-Tex is offline   Reply With Quote
Old 08-03-2009, 03:40 PM   #11
Elite Member
iTrader: (46)
 
Stein's Avatar
 
Join Date: Dec 2007
Location: Nebraska
Posts: 4,812
Total Cats: 138
Default

Quote:
Originally Posted by ZX-Tex View Post
Nice. If that is what I think it is, I will be using that feature.
Damn smart people.
Stein is offline   Reply With Quote
Old 08-03-2009, 04:52 PM   #12
y8s
2 Props,3 Dildos,& 1 Cat
iTrader: (8)
 
y8s's Avatar
 
Join Date: Jun 2005
Location: Fake Virginia
Posts: 19,038
Total Cats: 407
Default

argh. the logging filename feature is still broken in the first few days of the month.
y8s is offline   Reply With Quote
Old 08-06-2009, 12:59 PM   #13
Murderator
iTrader: (76)
 
18psi's Avatar
 
Join Date: Apr 2008
Posts: 36,206
Total Cats: 2,587
Default Big problem

Ok, has anyone used this yet?

I just did. Flashed it with FlashitV1 and loaded my map like usual, start the car and notice its kinda weird (like the car is vibrating, but rpm are steady). Ok, no big deal I'll let it warm up and take it for a spin. Take it for a spin, go into boost, and...

FUEL CUT!
Wtf, I try it again. It starts cutting fuel and killing all power as soon as I get into boost. Then I look at the "gauges" window and ITS RUNNING ON OEM O2 SENSOR! WTF????

There is absolutely no serial communication between the adaptronic and my aem uego. I tweak with it for a good 20 minutes, nothing I do works. I get out and inspect all the connections: they're perfect.

I go home and reload the old firmware. Car starts right up, idles decent like before, and now my wbo2 is communicating with the Adap with no problems.

AM I DOING SOMETHING WRONG OR IS THIS A GLITCH/PROBLEM?

I thought it was something on my end til I flashed the old firmware back in and it worked fine again.
18psi is offline   Reply With Quote
Old 08-06-2009, 01:13 PM   #14
Senior Member
iTrader: (19)
 
Join Date: Oct 2007
Location: MoCo, MD
Posts: 703
Total Cats: 0
Default

I noticed that as well. Analog tab is set to OEM NB sensor, LC-1 is selected in the special functions (?) tab. I'm just getting the car up and running, but AFR never went further than 14.5 -15.3, when the Innovate gauge was showing swings between 10.1 and 18.1.
pschmidt is offline   Reply With Quote
Old 08-06-2009, 01:37 PM   #15
Murderator
iTrader: (76)
 
18psi's Avatar
 
Join Date: Apr 2008
Posts: 36,206
Total Cats: 2,587
Default

Quote:
Originally Posted by pschmidt View Post
I noticed that as well. Analog tab is set to OEM NB sensor, LC-1 is selected in the special functions (?) tab. I'm just getting the car up and running, but AFR never went further than 14.5 -15.3, when the Innovate gauge was showing swings between 10.1 and 18.1.
Exactly. When I set my back up sensor to stock narrow band it reads just that: 14.2-15.5 and completely different from the aem. When I turn off the narrow band it doesn't read afr at all, while the aem gauge still does.

I'm pretty sure either something is fuxorzed with the new firmware or some settings changed disabling the wbo2 that we were not told about.

I'm back on the old firmware til this is figured out, since it works fine.
18psi is offline   Reply With Quote
Old 08-06-2009, 02:13 PM   #16
Elite Member
Thread Starter
iTrader: (9)
 
Join Date: Jun 2008
Location: Houston, TX
Posts: 1,583
Total Cats: 8
Default

I'll send a message over to rob...
TravisR is offline   Reply With Quote
Old 08-06-2009, 08:23 PM   #17
Senior Member
iTrader: (19)
 
Join Date: Oct 2007
Location: MoCo, MD
Posts: 703
Total Cats: 0
Default

Reverted back to the old firmware, and still can't get a reading from the LC-1.
pschmidt is offline   Reply With Quote
Old 08-07-2009, 09:54 AM   #18
Elite Member
Thread Starter
iTrader: (9)
 
Join Date: Jun 2008
Location: Houston, TX
Posts: 1,583
Total Cats: 8
Default

Just so you guys know Rob believes he has tracked down the problem in the firmware. He's temporarily removed the update and is now working to fix it.
TravisR is offline   Reply With Quote
Old 08-07-2009, 12:20 PM   #19
Junior Member
iTrader: (9)
 
Join Date: Jan 2007
Posts: 455
Total Cats: 3
Default

I drove to work this morning with the new firmware installed - glad I brought the laptop along. No UEGO issues though.
sv650_ck is offline   Reply With Quote
Old 08-07-2009, 12:24 PM   #20
Elite Member
Thread Starter
iTrader: (9)
 
Join Date: Jun 2008
Location: Houston, TX
Posts: 1,583
Total Cats: 8
Default

Sorry guys
TravisR is offline   Reply With Quote
 
 
Reply

Related Topics
Thread Thread Starter Forum Replies Last Post
The Definitive "VVT swap into 90-97 chassis" Megathread. Savington Engine Performance 496 11-13-2017 12:12 PM


Thread Tools Search this Thread
Search this Thread:

Advanced Search

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Trackbacks are Off
Pingbacks are Off
Refbacks are Off



All times are GMT -4. The time now is 07:15 AM.