99, I just read your whole thread....every word! I was excited before, but now F*CKME! I can't wait to get mine done.......EFR6258 should be here this week, then block head go to machine shop for some black voodoo magic and then I can finally start putting my shit together. Thanks for the carporn to keep me going.....

There's a discussion thread in the local forum:
CrucesStreets.com - View topic - 2013 ASR Super Lap Mega thread: dates, rules, discussion etc

Basically, your car must be in good condition, good seatbelt or harness, good brakes, no missing lug nuts, good battery holder. No loose objects in the car. The car will be checked before getting onto the track. Loaner helmets are available if you don't have one.

Thanks! You are going to love it!

I'm planning to get the car back to the dyno with the new Enhanced-DIYPNP to check the tune for next season. This evening I decided to check things out first. I changed the EFR V-band clamp with the beefier one from Treadstone.

https://www.miataturbo.net/attachmen...ine=1362727256

https://www.miataturbo.net/attachmen...ine=1362727256

How on earth is your car so clean? Mine is covered with shit already... but I do drive it often.

My car is dirty. We get mostly dust here in the desert. I hose off the engine bay every time I wash the car.

What are you using for the ducting? Is that steel?

I used aluminum sheet.

Tomorrow is dyno day for the new MSLabs Enhanced DIYPNP ECU, I'll post new numbers...

oh snap, can't wait for the glory:D

Please make sure its legible this time.

323WHP / 262WTQ @ 14 PSI

https://www.miataturbo.net/attachmen...ine=1363126598

Those are GREAT numbers for such low pressure, 'GRATS MAN :)

Something kinda bugs me though: the area between 3600-5200. Looks like its either boost or spark limited to look that way, and could have been rounded to the left a little bit like the rest of the curve and other "normal" curves

Also any reason you didnt' wind it out to at least 7? Looks like it woulda kept making power

Is that wastegate only maybe? I am also confused, that turbo should have no problem making 250ft-lbs at 4000rpm and then holding it there.

curious to see the boost log.

Yeah something must be up. 150whp@4k and 200wtrq@4k seems low.

That top end looks amazing, though. Square top doin' work like a mug.

I have read this all before, but to save me from doing so again, can you please recap what your engine specs are? I am building an EFR6258 very soon and want to know how my setup compares to yours. Great thread with lots of pictures, thank you. So, compression ratio? Head work? intake? The important stuff that determines those numbers? Thanks in advance!
-Chris

Great numbers! Everyone is right about the mid torque and getting that torque up should help with perhaps more power up top!

I believe it is in his signature!

Yeah, I am a dumbass! I started reading at the beginning again and got to page three before I made my last post.....never looked at the sig....lol. Thanks 7!

But was there any head work? VVT head?

Thanks all!
I mentioned to him while we were tuning that it seemed to have a flat spot in the middle. After viewing logs of the pulls he saw that some timing was being pulled. I'm not sure it its related to the flat spot. Reverant's new ECU has some sweet knock sensing settings. In the end, the tuner pulled some timing to avoid it. The summer will be worse so, the timing map will be a good starting point to let the ECU compensate.

The head is a 99 head that has the ports smoothed to remove casting flash, the valve ports were smoothed to have better transitions to the valves, the combustion chambers were smoothed out and valves were deshrouded.

I can send logs to you Scott. email OK? (I have it.)

99MX5, is your head stock? What intake mani are you using?

See above post about the head. The manifold is a Squaretop.