Aidan's loose oily bunghole actually runs a track lap
#523
SADFab Destructive Testing Engineer
Thread Starter
iTrader: (5)
Join Date: Apr 2014
Location: Beaverton, USA
Posts: 18,642
Total Cats: 1,866
Searched back through my thread and I found deezums saying that 1/8 NPT will fit in 1/8 BSP, I'm 90% sure but need to find a 100% source before I screw something into my aluminum head and **** it all up. We have all seen what I am capable of here.
#529
SADFab Destructive Testing Engineer
Thread Starter
iTrader: (5)
Join Date: Apr 2014
Location: Beaverton, USA
Posts: 18,642
Total Cats: 1,866
Nice little diff leak...hopefully its fixed now, first axle seal job.
Update to the list:
To-Do:
0. FIND OIL LEAK/BURN (So far so good.)
1. Inconel studs (RX-7 ordered, still need resbond but I think I am going to run without resbond for now because its a biatch to find)
2. Exhaust bracing. (Ordered a 3 inch exhaust clamp)
3. Locking downpipe bolts (Arrived)
4. Seats + Harness
4. Back braces (DIY)
5.Install new springs (550 Front, 350 rear)
6. Oil+water temp guages. (Going with a VEI systems gauge) Ordered
7. Helmet (Going to continue to run my open face helmet and wait for sa-2015)
8. Hardtop (Got one)
9. Put beads on intercooler pipes (Probably DIY: DIY $5 charge pipe bead roller - D-series.org, unless someone local knows somewhere to get it done cheap)
10. Find coolant leak. (risky to put this here but so far I haven't lost any coolant)
11. Find diff leak.
12. Heat Shielding. (master cylinder, brake lines)
13. Tune.
14. Manifold relief cuts
∞. Break stuff
Update to the list:
To-Do:
2. Exhaust bracing. (Ordered a 3 inch exhaust clamp)
4. Back braces (DIY)
5.
6. Oil+water temp guages. (Going with a VEI systems gauge) Ordered
9. Put beads on intercooler pipes (Probably DIY: DIY $5 charge pipe bead roller - D-series.org, unless someone local knows somewhere to get it done cheap)
12. Heat Shielding. (master cylinder, brake lines)
13. Tune.
14. Manifold relief cuts
∞. Break stuff
#532
SADFab Destructive Testing Engineer
Thread Starter
iTrader: (5)
Join Date: Apr 2014
Location: Beaverton, USA
Posts: 18,642
Total Cats: 1,866
I also need to do some ducting, thats a whole bunch more research I have to do. Hoping hi_im_sean or deezums does something cool because they have the same intercooler I do. Then I can just copy that.
#534
SADFab Destructive Testing Engineer
Thread Starter
iTrader: (5)
Join Date: Apr 2014
Location: Beaverton, USA
Posts: 18,642
Total Cats: 1,866
Haha, its going to be last on my list. I don't think I'm a fast enough driver to need it with the reroute, and the lack of extreme temperatures up here. But its definitely in the back of my mind.
#539
Elite Member
iTrader: (3)
Join Date: Apr 2014
Location: Huntington, Indiana
Posts: 2,885
Total Cats: 616
Speaking of dick jokes, I figured out what happened to your package.
I guess I overwhelmed the poor girl at the UPS store with the number and... flashiness of packages that I sent out. Yours got set to the side and forgotten about without a shipping label.
They made it right and are sending it out for delivery on Monday.
Edit: I just found out they dropped the ball on Girz0r's package as well. I may need to find a new shipper, but I truly hate Fedex.
I guess I overwhelmed the poor girl at the UPS store with the number and... flashiness of packages that I sent out. Yours got set to the side and forgotten about without a shipping label.
They made it right and are sending it out for delivery on Monday.
Edit: I just found out they dropped the ball on Girz0r's package as well. I may need to find a new shipper, but I truly hate Fedex.