I don't think it is going to be a kit that's for sale from the sounds of it. There's a lot of custom work that goes into the swap. A lot of modifying of the actual bellhousing. If you look in my thread you can see just what I'm talking about. Other than the adaptor plate and mounts to the chassis I'm not sure what else you could get that would make it a "kit".

Fuuuuuuuuuuuuuuuuuuuuuuuuuuuuuuuuuuuuuuuuuuuuuuuuu uuuuuu.

SO EXCITE.

I just want an FD trans mount kit.

FD or FC?

I said... i just want an FD trans mount kit. :giggle:

Trans mount? or PPF adapter.

Goddamnit.

Goddamnit or God bless you?

Delete PPF. Win.

It's begun. *edit, it's begun again. Stripped a bunch of the seam sealer out and started to tack it up. Turns out I'm not going to be able to tig most of these seams very easily so I'll have to dust off the old Mig welder...

https://www.miataturbo.net/attachmen...ine=1423889826

That looks all too familiar! I better beat you to finish since I'm not going to beat you once we're both running

One of these days I'll have to blitz through this entire thread. Not nearly as long as Jeff's, but an awesome car none the least.

Pulled the turbo out for removal of the compressor side, it's going out to be coated to match the FPR and EWG.

https://www.miataturbo.net/attachmen...ine=1424318235

Engine is removed, bay is stripped and etching primer has been applied anywhere necessary.

I've decided to do a brake booster delete setup (after speaking with my Wilwood rep I'll likely not take this master route) but and completely tuck the brake lines:

https://www.miataturbo.net/attachmen...ine=1424318235

https://www.miataturbo.net/attachmen...ine=1424318235

Small update while I wait for Epoxy Primer to set up. Pulled the engine, pulled the dash, pulled the wiring and blasted everything out from the cracks. Went through and ground down areas of chipping paint, in most places this resulted in bare metal.

Bare metal should always be hit with some etching primer, usually it's this ugly green color:
https://www.miataturbo.net/attachmen...ine=1424926124

The Epoxy primer went on - I decided to use this specific primer for a solid chemical adhesion because of the harsh nature of an engine bay. Most of the bay was prepped with 220 grit sandpaper and this primer should do a great job filling that with a coat thickness of 1.3-1.6mm.

https://www.miataturbo.net/attachmen...ine=1424926124

Cleaned the gun out and I'll give this an hour to set up and hit it with a light scuff - being a 2 part primer it should set up nicely by then but it's been years since I've painted anything.

Looking good! I can't paint to save my life.

Bare steel is fine with no etching primer, its aluminum that needs it most, SS and other self oxidizing metals can go either way. I mean its not going to hurt, and you could always just give it a wipe down with muriatic acid before painting as well if you didnt want green but wanted it etched.

I see the super duper throwout bearing in that pic. How did it hold up? I bought one but haven't installed it yet. Is that a dark picture or do I see oil inside the bellhousing?

Like a charm. OE style replacement exploded with the quickness.

I was able to get a thing or two done this weekend. Finally finished prep on the bay and shot some paint and clear coat. The basecoat showed some signs of contamination and it turned out to be some water in the compressor... Drained it and ran an inline filter and it went on like glass.

https://www.miataturbo.net/attachmen...ine=1425526751
https://www.miataturbo.net/attachmen...ine=1425526751
https://www.miataturbo.net/attachmen...ine=1425526751

Now it's time to route the brake lines.. I picked up stainless hardline which is just a pretty version of your standard brake line. All of the fittings will be black 3an fittings. Should come together really nicely if I can find time.

This is bit of a jump in progress but as Fab9 continues to grow I have less and less time to work on it and update build threads, unfortunately. Now we're in a bit of a rush to finish the car before Miatas at the Gap/Tail of the Dragon. Here is a link to the blog post, if any of you will be attending we'd like to meet you: Fab9Tuning Blog

http://www.miataforumz.com/attachmen...ine=1435068200

A couple of recent changes - we decided to go with the TEIN Monosport because we kept selling out of the TEIN Flex Systems and I think we will take better advantage of the Monosport configuration. (I ended up shipping my personal set of Street Flex to a customer).

Swaybar setup changed, went with the reinforced swaybar mounts and Whiteline sealed end links (both listed on the site).

New ish fuel configuration to acomodate the fuelab 515 regulator.

https://www.miataturbo.net/attachmen...ine=1435075130

Got rid of the GM 3 Bar Map sensor and installed the AEM 5 bar to support the higher boost levels we expect to tune the EFR on. Also finished most of the engine side wiring..

https://www.miataturbo.net/attachmen...ine=1435075130

This was just to fill a curiosity I had, I'll likely end up with Wilwood stickers back on here. Looks a bit busy for my taste.

https://c1.staticflickr.com/1/277/18...4e7a1a7b_z.jpg