Building a blonde young beefcake wearing nothing but skimpy shorts named Rocky
1 Attachment(s)
Hello All,
Picked up a 2002, recently sold a 91 Supercharged. I'm picky about my work and try to make the right moves with my stuff. I hope you enjoy. Equipment: 2002 Miata LS White, black and tan interior Corbeau FX1 Pro Suede Drivers Seat OZ Superleggera 16 Tein S-Tech Springs, KYB Shocks Performance: BEGI S4 System with upgraded intercooler and GT2860RS option (Disco Potato) AEM Water/Meth Progressive from 4-13 LBS (Not tuned as of now) ACT Clutch on my third 5 speed trans LSD Poly Differential bushings FM turbo exhaust with high flow cat Poly exhaust hangers AEM WB TurboSmart E-Boost2 Controller XEDE Piggy back RC 550 injectors Walbro 190 HP Fuel Pump Upgraded radiator - Coolant Reroute Marshall - Boost, Oil Pressure, Oil Temp gauges Roll bar - Hard dog I'm sure I'm missing things.. https://www.miataturbo.net/attachmen...ine=1315511494 |
7 Attachment(s)
AEM Meth/Water Install:
I decided to run the pump and the tank in the trunk. I pride my engine bay too much to be cluttering it up with another tank and a bunch of wires. https://www.miataturbo.net/attachmen...ine=1315511595 https://www.miataturbo.net/attachmen...ine=1315511595 Time to cover up my gorilla welding. https://www.miataturbo.net/attachmen...ine=1315511595 I think it came out decently. https://www.miataturbo.net/attachmen...ine=1315511595 Lightweight Battery installation: Old mount was obviously too large. I didn't want to rice it up with some rigged up stuff though. https://www.miataturbo.net/attachmen...ine=1315511595 So I chopped the grip off and re-welded it to fit the new battery. https://www.miataturbo.net/attachmen...ine=1315511595 A little black paint, some new terminals and shrink wrap, and we're in business. Just can't leave my radio on as long when the car is off. https://www.miataturbo.net/attachmen...ine=1315511595 |
3 Attachment(s)
Radiator and fan installation:
We had a heat wave come through and the car started to overheat under some moderate beating-the-shit-out-of-her driving. I didn't see any reason to dump 5 hundo on brand name aluminum when I was just looking for a little upgrade, so I ordered this guy off of eBay. Nice product, direct fit, and it absolutely did the trick. Threw some Mishimoto silicone on it. Product Link Good looking radiator if you ask me. It's got a simple job. Good welds, factory mounting points. https://www.miataturbo.net/attachmen...ine=1315511716 Slid in with minimal fuss, looks good to me. https://www.miataturbo.net/attachmen...ine=1315511716 The slim fans made up for the additional size of the radiator. Mishimoto silicone was designed for the stock coolant route.. so that took some manipulating. Nothing to fuss about though. https://www.miataturbo.net/attachmen...ine=1315511716 |
5 Attachment(s)
You could call this a bump in the road. Or a hugefuckingholeinmyturbo. Turns out all of the recent tuning i've been required to do is not because of elevation change, or change in the weather... or the gas I pump.. or anything else but this big ass hole. Unmetered air. A whole lot of it. My guess is that to maintain 10-11 LBS at the manifold, this turbo has likely been producing over 35PSI.. 24 of which have been flowing out of this hole. This is the cause of my turbo lag too. Good thing I didn't order that custom plate..(TRBO LAG)
https://www.miataturbo.net/attachmen...ine=1315511780 Welded her up and shes good as new. Can't wait to see what I've been missing out on. Best part is- I've still been wrecking people :) https://www.miataturbo.net/attachmen...ine=1315511780 I'm not a patient man, but I'm not the type to rig some bullshit up. During reassembly, I noticed I was missing the gasket from turbo to down-pipe. I called dealerships for cars that came with a similar gasket, I called friends of mine who had turbo setups in the past.. nothing. Sadlife. Being the crafty type- I went to ACE hardware and picked up a sheet of aluminum. Rather thick but soft a soft metal. I traced out my DP and started to cut the aluminum. After i had the shape cut I took a block sander with some 600 grit sandpaper and blocked it flat. Perfectly flat. https://www.miataturbo.net/attachmen...ine=1315511780 Didn't come out too bad! I hope this will do the job because it's a bitch to remove the DP on the BEGi setup. At one point, I was required to cut a 13mm open ended wrench in half. I went and bought a duralast wrench because I couldn't bare the thought of taking a cut off wheel to my precious snap on :) https://www.miataturbo.net/attachmen...ine=1315511780 There we have it. As you can see, I've wrapped the stainless lines with rubber hose this time around just to be safe. https://www.miataturbo.net/attachmen...ine=1315511780 |
4 Attachment(s)
The engine bay was a little trashy looking before and definitely not my style:
BEFORE https://www.miataturbo.net/attachmen...ine=1315511827 AFTER -I used degreaser to hit the spots with buildup, scuff pads on the oxidized aluminum, wire wheel on the stainless, and nylon woven loom to clean up some wires. I took brackets off from small to large and coated them with a durable paint. I used VHT Wrinkle black to hit all of my heat shields. Aluminum looks good no doubt, but not when I actually have to use the car. It's way to hard to maintain and I like the OEM look of the Wrinkle Black. https://www.miataturbo.net/attachmen...ine=1315511827 The VHT goes on with a bit of a sheen and then I baked it in the booth. Comes out like JDM wrinkle valve covers :) https://www.miataturbo.net/attachmen...ine=1315511827 Came together nicely in my opinion. https://www.miataturbo.net/attachmen...ine=1315511827 |
Nice car. I'd daily that ho. What kind of numbers at high and low boost?
|
10 Attachment(s)
It's time for a fuel pump. Old one might be tired, or reached it's limitations (those of which I don't know). I went with the Walbro 255 High Pressure version. It should suit my needs and it's not known to be loud. I purchased the install kit with it, although the only thing I used from the install kit was the filter and the isolator. The whole project took me maybe 35 minutes while taking pictures for you guys.
Pump is accessible from the rear deck inside the car. I lifted the carpet, removed the plate and BAM! Fuel pump assembly. https://www.miataturbo.net/attachmen...ine=1315511886 To avoid the smell of fuel in my car for weeks to come, i've decided to protect the area from spillage.. https://www.miataturbo.net/attachmen...ine=1315511886 Disconnected my lines, pulled them to the side with the rag and unbolted my fuel assembly. She's ready to come up. https://www.miataturbo.net/attachmen...ine=1315511886 Came out quite easily - Remember to let the filter bag drain. It does this slowly but it's better than dripping fuel all over your carpet https://www.miataturbo.net/attachmen...ine=1315511886 She's out.. Looks.. like a fuel pump. https://www.miataturbo.net/attachmen...ine=1315511886 New - Old https://www.miataturbo.net/attachmen...ine=1315511886 The stock connectors were not compatible with my new pump.. The new pump had a couple of male spades inside of a proprietary looking connector. https://www.miataturbo.net/attachmen...ine=1315511886 Chopped those off and used female spades, with a little heat shrink tubing. (Don't use a lighter to shrink btw) https://www.miataturbo.net/attachmen...ine=1315511886 New pump installed and on it's way back to the car. https://www.miataturbo.net/attachmen...ine=1315511886 Decided to touch up the bottom and top of the plate with some noise dampening material. Just in case it's louder. https://www.miataturbo.net/attachmen...ine=1315511886 Slapped it back together, cycled the key a couple of times to clear any air and prime the fuel system... she started right up. |
5 Attachment(s)
So before I start tuning for methanol injection, I'd like to make sure the damn thing is doing what I expect it to. Quite possibly the best solution for this is the AEM Monitor system.
AEM Water Methanol FAILSAFE device - AEM part # 30-3020 MSRP 263.83 This was my choice because I'm using the AEM progressive meth system. I want to control when it comes on and I want to know how much is spraying during my power-band. Comfortable Keyboard not included. https://www.miataturbo.net/attachmen...ine=1315511919 https://www.miataturbo.net/attachmen...ine=1315511919 Looks good on my desk, let's see how it looks in my car. Wiring: Constant power Ignition power Ground Fail communication wire to my meth controller Pump signal wire Illumination Harness to flow sensor USB cable for communication to laptop software If you've followed my thread so far, you'd know that I ran my pump and tank from the back of the car. This allowed me to simply tap the meth line under my carpet instead of installing it in the bay. This is a major plus for me for a couple of reasons - I like my engine bay clean, I don't have to run another wire through my firewall and the sensor is not exposed to harsh engine bay conditions. I have absolutely run out of places for gauges and I really dislike the idea of removing a vent for a gauge but I had to sacrifice for now. I'll miss my 25% less upper dash air conditioning. https://www.miataturbo.net/attachmen...ine=1315511919 Gauge looks great. The software allows you to control the gauge color, needle intensity, warning method (needle flashing, backlight flashing, or both and how fast they flash). Pretty cool. https://www.miataturbo.net/attachmen...ine=1315511919 So the software is designed to monitor your system in working order, then set parameters in which it will send you a warning. The gauge harness also has a couple of output wires to trigger different functions - Warning lights, Map changes, Sound your horn, lock your doors.. whatever. It's two wires with controllable polarity good job AEM. As you begin to drive, you will see your injection properties in yellow dots. To the right you will see a loading bar. Once you drive hit boost enough times it will go to the 100% mark and you can click "Auto Set Limits". This will create warning limits based on how the system has behaved under working conditions. It's always been a little too tight for my liking and will trigger all the time, but maybe that's due to how little I drove it under normal conditions before setting it. So I set mine manually. https://www.miataturbo.net/attachmen...ine=1315511919 With my setup, it will start spraying before the monitor will register anything. I think this is due to the fact that I'm really not running much methanol. After running through a tank of meth and refilling it, I could not get it to spray again. This is very likely due to the orientation of my pump. I mounted it right side up, next to my tank. The inlet of the tank should be lower than the outlet of the fluid tank. I might have a bum pump but I'll flip it over before I draw any conclusions. GOOD THING I INSTALLED THIS SYSTEM BEFORE TUNING |
2 Attachment(s)
A couple of weeks back I was doing some tuning.. (on my car with a huge hole in my turbo) I came around the corner just down the street from my house and slammed it into second gear. I heard an odd noise which I immediately assumed was rod knock. I shut it down and coasted into my driveway... it made a noise until I put the clutch to the floor then it stopped... Engine sounded perfectly healthy. Clutch exploded? Maybe. I rocked the car back in reverse and it made a noise and felt like it bound up when the noise happened so I parked it. Pulled the trans and the clutch looked good...
Pulled the trans apart an found this guy.. Poor transmission.. it only had 45k on it. The 5 speed has a known reliability issue above 250 horse. I'm lucky it has lasted this long. https://www.miataturbo.net/attachmen...ine=1315511945 Picked up another trans, what better use for the daily leather seats? https://www.miataturbo.net/attachmen...ine=1315511945 Threw the trans in and she was back on the road. |
6 Attachment(s)
Today's weight reduction:
https://www.miataturbo.net/attachmen...ine=1315511997 An alpine CDA-9886 with a head unit power pack. Sounded alright but I happen to work for the company that has just produced the first Android Based head unit. ...Internet connectivity, applications, Google Maps + GPS antenna, 4xUSB, 55x4 output.. It's a very nice piece. https://www.miataturbo.net/attachmen...ine=1315511997 Slapped it in real quick and it looks good :) Quite an upgrade in sound quality too! Seems like it's got a better range of sound. https://www.miataturbo.net/attachmen...ine=1315511997 Bosch valve leaking. Leaking bad. Anything else trying to slow down my spool time? Damn. Picking up a new valve today. New Valve acquired: Synapse Engineering Synchronic DV Replacement Kit for Bosch BPV Manufacturer: Porsche Product ID: DV001A.010 You might call this the not-fucking-around solution to diverter valves. https://www.miataturbo.net/attachmen...ine=1315511997 https://www.miataturbo.net/attachmen...ine=1315511997 https://www.miataturbo.net/attachmen...ine=1315511997 First thoughts: Awesome construction, nice and small. DEATH TO THE DIAPHRAGM! Its a piston actuator! Comes with hard vacuum lines and quick connect fittings. Also includes threaded nipples for traditional vacuum lines. Some type of miniature v band looking inlet and outlet pieces, should be a direct replacement for the busted Bosch I'm running now. I'll install after work and get you fools some pictures. |
9 Attachment(s)
Here is my busted ass Bosch.
https://www.miataturbo.net/attachmen...ine=1315512031 So the project was immediately off to a start that brought me to an auto parts store. The inlet and outlet sizes of my Bosch valve were different than my Synapse. https://www.miataturbo.net/attachmen...ine=1315512031 I shot down the street and picked up 1" rubber hose to void the gap and it worked out perfectly. The 1" fit very firmly and my previous couplers fit very firmly over those. Problem solved. https://www.miataturbo.net/attachmen...ine=1315512031 The vacuum fittings are beautiful. https://www.miataturbo.net/attachmen...ine=1315512031 While I was under the hood I noticed the hard vacuum line running across the firewall was particularly ugly. The factory finish had oxidized and I didn't want to look at it anymore. I pulled it off and began to scuff it. https://www.miataturbo.net/attachmen...ine=1315512031 The usual suspects helped me with this one. Etching primer for metal and some durable flat black paint. I taped the ends to avoid the paint heating up and acting as a lubricant to my vacuum lines. https://www.miataturbo.net/attachmen...ine=1315512031 https://www.miataturbo.net/attachmen...ine=1315512031 Installed vacuum line: https://www.miataturbo.net/attachmen...ine=1315512031 Quick up the skirt shot: https://www.miataturbo.net/attachmen...ine=1315512031 Review: Fuckingexcellent. Nice firm release, no flutter with stock settings, sounds similar to the forge atmospheric valve (Which I happen to like). Clean sound and good performance. Quite enough to keep my customized license plate legitimate. During the installation I ran into a vacuum distribution block that had been leaking so I repaired it as well. Now the car starts with a nice firm -18 -19 on my vacuum gauge. |
1 Attachment(s)
So I was having some issues with unpredictable performance and an odd idle at times. My first thought was ignition. When I purchased the car from Texas I flew my brother out to drive it back for me, and I mailed new BKR7E plugs to the previous owner to toss in the car for me. BKR7E is one step colder than the stock plug and is the plug of choice for the boosted Miata guys.
The first plug I pulled looked awful for only having 5k on it. Looked like it had been run very rich for a period of time. https://www.miataturbo.net/attachmen...ine=1315512078 Second plug was the same, and when I tried to remove the third plug, the socket wouldn't drop down? After inspection it looked like the rubber grip from the socket that was used to remove the plug previously had stayed with the installed spark plug... Not sure why the hell you'd leave it on the plug or how the coil boot made decent contact with that on there but either way.. its half assed work. The fourth plug brought up another issue.. I noticed it say BKR6E on the side.. That futhermucker didn't install the plugs I had sent him. After tossing in the new set, she stated right up and idled like a champ. Drivability was smoother and performance under boost was consistent. |
2 Attachment(s)
After staring at the car for a couple of hours with some buddies we realized it's missing a mean stance from the rear wheels. It's very close but a subtle offset would do the trick.
I ordered 7MM hub centric wheel spacers and tossed them on. I don't ever recommend someone trying to correct any more than 8MM of offset without changing wheels. It's not usually the right way to go about it. But I'm comfortable with 7MM. https://www.miataturbo.net/attachmen...ine=1315512100 I'd have to say, this definitely did the trick. Much more aggressive ass end now. https://www.miataturbo.net/attachmen...ine=1315512100 |
1 Attachment(s)
Went out and had a buddy drive my car next to us.. First time I've seen it driving. The bitch looks real good.
https://www.miataturbo.net/attachmen...ine=1315512119 Video.. quick but fun. |
4 Attachment(s)
Tuning tonight for meth. I have a knock sensor on the car but I don't trust it and I can't monitor it's feedback. So I've decided to go the Det Can route.
Detonation Cans are used to listen to the physical knock of an engine. Known to be extremely reliable and it's been said that knock sensors will almost never beat the human ear when it comes to knock detection. You can make your own very easily and the performance is incredible. Required: - Ear protection headphones - Copper pipe - PVC air compressor hose I ended up spending around 40 bucks but you can do it cheaper. I started with the copper pipe, the idea is to attach one end to the engine block somewhere and the other to the air compressor hose. I flattened the end with a hammer and made a couple of folds to drill through. https://www.miataturbo.net/attachmen...ine=1315512155 Then you've got to run the other end into the headset. My headset was ABS plastic and had a foam insert that was easy to remove. I drilled to a slightly smaller size than my air line fitting and it threaded into the plastic. https://www.miataturbo.net/attachmen...ine=1315512155 How cool will I look when I'm tuning?! https://www.miataturbo.net/attachmen...ine=1315512155 The other end is attached to the engine. https://www.miataturbo.net/attachmen...ine=1315512155 They worked great! You can hear the engine internals extremely well. It was too hot for my taste last night so I decided to push the project off to another day but I did advance the timing under boost by 2 degrees without hearing any knock so that's promising. Bring on the power. |
6 Attachment(s)
Well I took a buddy of mine to the airport on Sunday and she didn't make it home.. I was cruising at about 70 and the bottom end took a shit. Blew something right through my oil pan. I pulled off and called a tow truck.
It wasn't tuned for the meth yet but I had recently added more fuel under the high boost areas. The cause of the failure is likely just the limitations of the stock block. Most people don't make this much power on a stock block and it lasts them long. I had a safe tune with no knock and strong fuel, it was just too much boost for the little 1.8. https://www.miataturbo.net/attachmen...ine=1315513075 https://www.miataturbo.net/attachmen...ine=1315513075 So I sit, listen to some good jams and wait for a tow truck. https://www.miataturbo.net/attachmen...ine=1315513075 https://www.miataturbo.net/attachmen...ine=1315513075 https://www.miataturbo.net/attachmen...ine=1315513075 https://www.miataturbo.net/attachmen...ine=1315513075 I was waiting for this day, and I thank the little bitch for making it through most of the summer, providing me with good times. Forged internals, stand alone ECU and about 22 LBS of boost will do me well for next summer. |
4 Attachment(s)
Now that I've got some down time to work on the little things that bug me... The meth gauge in the vent is killing me. Don't like it. So I ordered the single din radio mount for the gauges. I'll move the meth gauge here and finally install my Oil pressure, and analog boost gauge here.
The rings were silver and matched nothing so I went to my usual can of flat black and got to work. https://www.miataturbo.net/attachmen...ine=1315513109 https://www.miataturbo.net/attachmen...ine=1315513109 https://www.miataturbo.net/attachmen...ine=1315513109 https://www.miataturbo.net/attachmen...ine=1315513109 Looks much better if you ask me. The AEM gauge lights up the red/amber to match my factory gauges and dash lighting. The only ugly ass gauge I have left is my TurboSmart eBoost2 |
5 Attachment(s)
Made my way up and checked out the car last night... Started to remove a couple of small items here and there to see if I could get a good look at the carnage for you guys.
It feels a bit like spending a year on a puzzle and the feeling you get when it's time to COMPLETELY-FUCK-IT-UP and put it back into the box. https://www.miataturbo.net/attachmen...ine=1315575521 https://www.miataturbo.net/attachmen...ine=1315575521 Ooo a little piece of my oil pan eh? https://www.miataturbo.net/attachmen...ine=1315575521 Mmmm a little hole in my engine eh? (Passenger side) https://www.miataturbo.net/attachmen...ine=1315575521 Another hole in my engine... eh? (Drivers side) https://www.miataturbo.net/attachmen...ine=1315575521 And yes, I can shine a flashlight in one side of my block and it comes out the other :) |
I blame adding the gasket to the DP, it was totally an unnessecary move.
I didn't like your det can mounting location either. how much boost? |
Originally Posted by Braineack
(Post 769405)
I blame adding the gasket to the DP, it was totally an unnessecary move.
I didn't like your det can mounting location either. how much boost? Haha, the DP gasket was a boss ass move. The det can mounting was just for the picture. It was too hot for me to tune that day. Boost was 13.5 ish. |
2002 has 10:1 CR?
I think there's a good reason y8s keeps his boost below 10psi :) But, in serious, there was no gasket on the DP on purpose. |
Originally Posted by Braineack
(Post 769405)
I blame adding the gasket to the DP, it was totally an unnessecary move.
Very nice thread. I love the attention to detail and its coming along quite nicely. :bigtu: |
Originally Posted by Braineack
(Post 769427)
2002 has 10:1 CR?
I think there's a good reason y8s keeps his boost below 10psi :) But, in serious, there was no gasket on the DP on purpose. |
You may think the det-can location on the top of the head is fine, but if you move it to the block you'll hear less valve noise. I had a set-up like that for a while, you'll probably be much happier with it on the block.
Good luck with 10:1 compression, but still a great car. Does it weigh 2500lb yet? I've seen a few Miata blocks take 350whp for years just fine, even crewed for a 400+whp Miata that never killed the block. It's your tune or the stock rods...probably the rods. |
I'm sure he was well over 250rwtq.
|
Originally Posted by hustler
(Post 769448)
You may think the det-can location on the top of the head is fine, but if you move it to the block you'll hear less valve noise. I had a set-up like that for a while, you'll probably be much happier with it on the block.
Good luck with 10:1 compression, but still a great car. Does it weigh 2500lb yet? I've seen a few Miata blocks take 350whp for years just fine, even crewed for a 400+whp Miata that never killed the block. It's your tune or the stock rods...probably the rods. I'm having custom pistons made and I'm aiming for low 9:1 with a relatively light weight setup. My car weight is probably pretty decent, 15 pound seats, 13 pound wheels, spare + tools removed, lighter battery, soft top removed (hard top added but similar weights). Cooling system actually weighs less, and I've recently lost about 18 lbs myself ;) The roll bar, turbo, DP and exhaust are the only real weight adders. Significant but must haves. Why do you ask? |
Really nice car. I really dig painting mine white as well. Although yours needs a Megasquirt. ;)
|
I'm thinking Adaptronic. PM me some info on MS and change my mind. It seems you might be the person to talk to..
Your sig: Plug and Play Megasquirt ECUs for ANY 90-05 Miata |
Originally Posted by Dem768
(Post 769538)
I'm thinking Adaptronic. PM me some info on MS and change my mind. It seems you might be the person to talk to..
Your sig: Plug and Play Megasquirt ECUs for ANY 90-05 Miata |
Your car is a sexy bitch. Completely reminds me of my white sexy bitch.
Love the progress and what you've done with it. Good work. Reading through the thread I was going to suggest you get rid of that POS afm and gayxede. Looks like you read my mind and will be doing just that soon. Both the MS and Adaptronic are great and will work better than the xede imo. Good luck |
y8s has one for sale too if you PM him. he was just too lazy to ever put it online...was on his '01. But he's running MS3x now, and no it wasn't on accident.
|
Sucks about the block vents, threads like this always scare me. Definitely post some more pics once you get it pulled apart. Can't wait to see her come back even stronger.
|
Originally Posted by 18psi
(Post 769559)
Your car is a sexy bitch. Completely reminds me of my white sexy bitch.
Love the progress and what you've done with it. Good work. Reading through the thread I was going to suggest you get rid of that POS afm and gayxede. Looks like you read my mind and will be doing just that soon. Both the MS and Adaptronic are great and will work better than the xede imo. Good luck Looking hard, making it fast and keeping it clean is rarely done at one time during most builds. |
Originally Posted by Dem768
(Post 769423)
Boost was 13.5 ish.
|
Originally Posted by lsc224
(Post 770339)
What was your AFR's at 13.5?
|
Originally Posted by Braineack
(Post 770346)
Even if it was the most mathematically ideal perect AFR you could ever come up with 275rwhp on a 10:1 CR motor with stock rods is asking too much out of it. Those rods start to deform in the 250rwtq area, and that's about where he was at.
|
Hmm, some basic instructions in this build thread for those of us that are experienced, but then I noticed the lack of newbs asking stupid questions. Nice explanations.
Sorry about the vented block, what are the plans, have the back up engine already? You certainly move fast- built, upgraded, tranny replaced, more upgrades, cleaning, painting...all on one day! |
Originally Posted by lsc224
(Post 770349)
True! I was just curious where he was at.
|
Nice build thread. While you have the motor out, pick up a bigger turbo :)
|
6 Attachment(s)
Originally Posted by Faeflora
(Post 770743)
Nice build thread. While you have the motor out, pick up a bigger turbo :)
Carnage update: https://www.miataturbo.net/attachmen...ine=1315928224 https://www.miataturbo.net/attachmen...ine=1315928224 https://www.miataturbo.net/attachmen...ine=1315928224 YEP that's a broken rod... and someone who's had these motors apart tell me if that is a valve hanging or an oil tube? And in pic one.. NOTICE MY FLUCKING ALTERNATOR, it can be seen right through the motor.. |
In pic one that's an oil jet. Bent tube bolted on with an banjo bolt that shoots oil at the bottom of the pistons, looks surprising fine for a cooper tube in the middle of all that carnage. The good thing is that our motors are non-interference. The bad thing is that only counts for broken timing belts. All bets are off when the rod breaks, your valves are probably toast in at least one cylinder.
|
Oil squirter in that pic.
|
3 Attachment(s)
Started to remove a couple of small items here and there to see if I could get a good look at the carnage for you guys.
It feels a bit like spending a year on a puzzle and the shitty feeling you get when it's time to COMPLETELY-FUCK-IT-UP and put it back into the box. https://www.miataturbo.net/attachmen...ine=1315575521 https://www.miataturbo.net/attachmen...ine=1315575521 Ooo a little piece of my oil pan eh? https://www.miataturbo.net/attachmen...ine=1315575521 Mmmm a little hole in my engine eh? (Passenger side) https://www.miataturbo.net/attachmen...ine=1315575521 Another hole in my engine... eh? (Drivers side) https://www.miataturbo.net/attachmen...ine=1315575521 And yes, I can shine a flashlight in one side of my block and it comes out the other :) Made some time to pull the engine this past weekend. https://www.miataturbo.net/attachmen...ine=1317392205 https://www.miataturbo.net/attachmen...ine=1317392205 https://www.miataturbo.net/attachmen...ine=1317392205 Didn't take long to get her out. The damage is truly impressive. The pan is blown away, right side of the block has a softball sized hole and the left has a golf-ball sized hole. |
This car is so sexy. Looking forward to a new motor in this slut.
|
2 Attachment(s)
So I've purchased the Adaptronic ECU. It was second hand and came from a 99 so the harness is incomparable with my car. I used my old XEDE harness to adapt my new ECU for my car without having to splice my factory harness.
Reference Adaptronic Pinout>Cut>Strip>Solder>Heatshink... NEXT! Reference Adaptronic Pinout>Cut>Strip>Solder>Heatshink... NEXT! Reference Adaptronic Pinout>Cut>Strip>Solder>Heatshink... NEXT! Blah. Not pretty now but wait until I finish. The Adaptronic will actually allow me to use the factory ECU to control my idle valve which is handy for me because I hate tuning idle on a stand alone system. But in order to do this it must see a MAF, O2, and IAT. So I've got to fake those signals by wiring in 1k Resistors and then grounding it. https://www.miataturbo.net/attachmen...ine=1317825107 https://www.miataturbo.net/attachmen...ine=1317825107 More updates to come - I'm waiting for a couple of schottky diodes in the mail and I'll get it buttoned up. |
fap fap fap
|
Originally Posted by Braineack
(Post 770346)
Those rods start to deform in the 250rwtq area, and that's about where he was at.
|
1 Attachment(s)
Long time no update... I've received my new..ish engine. It's a Japanese 1.8 out of an NA Miata. I wasn't looking for a Japan motor because from my understanding there are no real differences but that's what showed up.
https://www.miataturbo.net/attachmen...ine=1321467378 So after some internal debate...haha get it? ...reading and pricing some things out. I've purchased my engine internals and they are as follows: Pistons: CP Pistons .5mm Oversize: 83.5 mm Bore 9.0 Compression Rods: Belfab H Beam Rods 600+ HP Bearings: ACL Main, Thrust and Rod bearings Head Gasket: OEM Mazda Hardware: ARP The only delay is the pistons. 2 weeks out but I'm not in a rush and I still need to dig into the new motor. |
yup thats an oil tube you can see where it bolts to the block its a piston squirter.
nevermind browser didnt update page properly. either way im lucky i only took a chunk out of my #3 piston then mine let go. Kris. |
Is a metal gasket better than a OEM one? If so i'd use that, no sense in forging the engine and not upgrading everything.
|
Wow, the car came along very well. Very clean. It sucks your motor grenaded :(
Good luck on the rebuilt |
Originally Posted by Bassmachine
(Post 796560)
Is a metal gasket better than a OEM one? If so i'd use that, no sense in forging the engine and not upgrading everything.
|
3 Attachment(s)
New rods showed up. Still waiting on pistons unfortunately. I tore down the old block in anticipation for machine work. It doesnt look too bad. My new slugs are only .5 over so this should be perfect. Being that the Miata runs an iron block nothing should be too out of order.
Belfab 600+HP rods: https://www.miataturbo.net/attachmen...ine=1322496825 OLD vs NEW.. The stock Miata rods really are some soft shit.. https://www.miataturbo.net/attachmen...ine=1322496825 New bearings and thrust washers are here as well.. https://www.miataturbo.net/attachmen...ine=1322496825 I've probably got another week until the Pistons show up so stay tuned. |
Hmmm. I like this thread. Though I'm surprised at only 13.5psi it let go.
|
2 Attachment(s)
Mmm.. So look what showed up today. :drool:
https://www.miataturbo.net/attachmen...ine=1322513574 https://www.miataturbo.net/attachmen...ine=1322513574 I'll be dropping the engine off at the machine shop tomorrow. :yippee: |
Damn I have the same rods and I forgot how frikken huge they are compared to the factory toothpicks.
MORE BIGGERER TURBOERRRE! |
Dropped off the pistons for dome and skirt coatings :) i'll have pictures in awhile.
|
1 Attachment(s)
Alright kids. Things are moving along with the quickness. Picked up the pistons and dropped them off with the Block, Rods, Rings, Bearings, Mains, Crank and hardware.
These sons of bitches are pretty: https://www.miataturbo.net/attachmen...ine=1322684759 |
UPDATE: Last night I went and tore the head off of the old block (because I'd like to use it on the new block) and it's all in tact! The thing looks clean! I'll bring it home and gasket match the intake and exhaust sides with a Dremel. I'll have it hot tanked and leak tested but nothing made contact with the piston so I'm a happy guy.
|
This is one of my favorite builds on here, LMK if there is anything you are looking for.
|
All times are GMT -4. The time now is 03:19 AM. |
© 2024 MH Sub I, LLC dba Internet Brands