Faelflora breaks his promise, time to part out car. GIT THE SAWZALL!
#3902
mkturbo.com
iTrader: (24)
Join Date: May 2006
Location: Charleston SC
Posts: 15,177
Total Cats: 1,681
I have offered to get it finished and running for Fae before. He just had to get the car down to me.
From when I last talked to him there were mechanical and tuning **** that needed to be done. I don't remember if any real fab work was needed or not.
From when I last talked to him there were mechanical and tuning **** that needed to be done. I don't remember if any real fab work was needed or not.
#3906
Moderator
iTrader: (12)
Join Date: Nov 2008
Location: Tampa, Florida
Posts: 20,664
Total Cats: 3,013
1. Buy a cheap beater Miata of same year model and color.
2. Put your VIN tag on it.
3. Get tested and pass
4. Move VIN tag back to your car.
5. Drive it
It's kinda like wearing a suit and tie to work to get paid, then going out to the club later in a dress, stockings, and lipstick to have a good time.
2. Put your VIN tag on it.
3. Get tested and pass
4. Move VIN tag back to your car.
5. Drive it
It's kinda like wearing a suit and tie to work to get paid, then going out to the club later in a dress, stockings, and lipstick to have a good time.
#3907
Elite Member
Thread Starter
iTrader: (2)
Join Date: Jan 2007
Location: Los Angeles, CA
Posts: 8,682
Total Cats: 130
1. Buy a cheap beater Miata of same year model and color.
2. Put your VIN tag on it.
3. Get tested and pass
4. Move VIN tag back to your car.
5. Drive it
It's kinda like wearing a suit and tie to work to get paid, then going out to the club later in a dress, stockings, and lipstick to have a good time.
2. Put your VIN tag on it.
3. Get tested and pass
4. Move VIN tag back to your car.
5. Drive it
It's kinda like wearing a suit and tie to work to get paid, then going out to the club later in a dress, stockings, and lipstick to have a good time.
VIN locations:
Front drivers side on dash under windshield (plate)
Door jamb next to strike plate on both sides (sticker)
Door next to latch on both sides (sticker)
Fire wall (1/4" tall stamped letters on welded plate)
Hood (sticker)
Front fender in water run-off gully on both sides (sticker)
Inside front bumper, passenger side, just under turn signal (sticker)
Trunk (sticker)
Inside rear drivers side fender just in front of bumper under gas fill hose (sticker)
Passenger side of aluminum oil pan (riveted metal plate)
PPF, top side roughly in center (stamped letters)
#3916
Moderator
iTrader: (12)
Join Date: Nov 2008
Location: Tampa, Florida
Posts: 20,664
Total Cats: 3,013
How many of you guys in California ever had a VIN checked anywhere other than the dash at the inspection station?
I suggested swapping it back immediately anyway. I would just say the car had been badly wrecked and was full of junkyard parts if anyone asked. And remove the extra VIN stickers from the junker anyway.
Y'all act like you never registered a stolen car before, lol. J/k
I suggested swapping it back immediately anyway. I would just say the car had been badly wrecked and was full of junkyard parts if anyone asked. And remove the extra VIN stickers from the junker anyway.
Y'all act like you never registered a stolen car before, lol. J/k
#3918
Boost Pope
iTrader: (8)
Join Date: Sep 2005
Location: Chicago. (The less-murder part.)
Posts: 33,050
Total Cats: 6,608
Not sure what they do if Earl Scheib carelessly painted over it.
#3920
It might be easier to just dash swap rather than swapping vin tags. You cant drill out the rivets with the dash in if the car has a windshield. Also, exact matching rivets have to be special ordered. You need the 3/16" flange size on a 1/4" rivet and the flange needs to be painted black. When I did the dash swap I just drilled everything out to use 3/16" but it doesnt quite look right.