are you retaining stock fans/shrouds with that mishi?
if so, shorten those stupid mounting points now while its easy. |
Originally Posted by 18psi
(Post 1160038)
are you retaining stock fans/shrouds with that mishi?
if so, shorten those stupid mounting points now while its easy. Thanks for the heads up on that! Keith PS: Looks like I will just keep the AC. Use it about twice a year, but not purchasing another part to get ride of it. |
Originally Posted by Twodoor
(Post 1160083)
Yeah, keeping stock fans. Didn't realize mounting points were too long.
Thanks for the heads up on that! Keith PS: Looks like I will just keep the AC. Use it about twice a year, but not purchasing another part to get ride of it. Remove A/C AND PS. Remove many parts. Cost none of the money. Win at life. Man pants. Cool kids. Etc. |
Originally Posted by 18psi
(Post 1160038)
are you retaining stock fans/shrouds with that mishi?
if so, shorten those stupid mounting points now while its easy. |
Looks like I can cut down a bunch of stuff and still have a gap at the bottom of the main fan, or I can stuff foam strips in the gaps, and duct tape around the edge's and call it a day.
Keith |
8 Attachment(s)
More pictures!
Rather than cutting down and re-tapping the radiator fan mounting points, I purchased two strips of air conditioning insulation foam rubber. https://www.miataturbo.net/attachmen...insulation-jpg I put this around the entire parimeter of the radiator fans, probably better air flow with this setup than their was stock! https://www.miataturbo.net/attachmen...iator-fans-jpg I finally figured out that the hose barb on the lower radiator hose connection at the mixing manifold is for the hose going to the oil / water distribution block for turbo water supply / return. I feel like the hole for the barb fitting was drilled in the wrong place, the barb fitting is pointed directly at the power steering pump, and the rubber hose run right behind the pulley. I don't think it is touching, but it would be hard to slide a piece of paper between them. https://www.miataturbo.net/attachmen...s-pulley-1-jpg https://www.miataturbo.net/attachmen...s-pulley-2-jpg I e-mailed Stephanie about it, and expect a response first thing Monday morning... oh wait, no... I mean I will have to call her to get her to open the e-mail and look at the pictures. Progress is being made! Keith |
Originally Posted by Twodoor;
I e-mailed Stephanie about it, and expect a response first thing Monday morning... oh wait, no... I mean I will have to call her to get her to open the e-mail and look at the pictures. Progress is being made! Keith That's another sign that you just need to take the whole pump out. People who can't handle manual steering in a miata need to exercise their forearms more.:jerkit: |
Originally Posted by Monk
(Post 1160574)
:rofl:
That's another sign that you just need to take the whole pump out. People who can't handle manual steering in a miata need to exercise their forearms more.:jerkit: What is your recommended method for depower if I decided to go that route? I only use the AC in the winter to help with de-fogging the windows, so if I do the depower, the AC is coming out as well... but from what I read I need a certain bolt to prevent an oil leak if I pull off the AC compressor. Keith |
8 Attachment(s)
More progress made, with some pictures.
I swapped out the RX8 425cc/min injectors for the 1000cc/min injectors BEGi sells. Came with a flow balance sheet with a crap load of test numbers, including the latency numbers at various battery voltages. Here are the RX8's about to come out and go up for sale: https://www.miataturbo.net/attachmen...t-come-out-jpg Here is a comparison between the old and new injectors. The new ones have the electrical connection lower down than the old injectors... but I didn't have any trouble connecting them. https://www.miataturbo.net/attachmen...egi-1000cc-jpg Here is a view of the business end of both. The RX8's have multiple small holes, the new 1000's seem to have one giant pintle. https://www.miataturbo.net/attachmen...-begi-1000-jpg And here are the 1000's in their new home. https://www.miataturbo.net/attachmen...000s-place-jpg Here is a tip for anyone doing injectors. The first time you do injectors take some RTV and stick the spacers in their correct locations. This makes it easier to get the fuel rail back in place, and the next time you pull the fuel rail there is no chance of a spacer dropping down into the depths of the engine never to be seen again. Keith |
Yes, you need to stuff a bolt in the hole the bracket leaves in the block. I forget the size. I'll try to find it in a sec. There are a few ways to depower the rack, but it's best to do it the FM way by cutting the seals. Here's their write-up: Flyin' Miata : Tech: 1.8 conversion
|
Originally Posted by Monk
(Post 1160670)
Yes, you need to stuff a bolt in the hole the bracket leaves in the block. I forget the size. I'll try to find it in a sec. There are a few ways to depower the rack, but it's best to do it the FM way by cutting the seals. Here's their write-up: Flyin' Miata : Tech: 1.8 conversion
I use this car year around, and really don't want to loose the AC for the defogging function. Amazing how much better dry air is at dispelling moisture! So, for now I will leave the hose where it is... Stephanie said she will talk to Corky about it and show him the pictures. Keith |
I dunno if you already posted this, but what turbo did you have shipped with your s6?
|
Originally Posted by 18psi
(Post 1160752)
I dunno if you already posted this, but what turbo did you have shipped with your s6?
Keith |
That's cool.
Though you're gonna have to keep it at a boner-killing 10ish psi if you want those stock rods to remain inside the block. Which should motivate you to build asap, because the difference between 10psi and 15+ on a spud is astronomical :party: |
Originally Posted by 18psi
(Post 1160809)
That's cool.
Though you're gonna have to keep it at a boner-killing 10ish psi if you want those stock rods to remain inside the block. Which should motivate you to build asap, because the difference between 10psi and 15+ on a spud is astronomical :party: Keith PS: At first of course it will be limited to the 10ish psi. Then after I vent the block with a busted rod the sky is the limit! |
12 Attachment(s)
Coolant re-rout complete!
Here is where the re-routed heater core line goes into the new lower radiator hose. https://www.miataturbo.net/attachmen...iator-hose-jpg Here is where I hose clamped the lower radiator hose to the swaybar to keep it away from the pulleys and belts. https://www.miataturbo.net/attachmen...d-sway-bar-jpg Here is the rear thermostat housing... got RTV everywhere putting that motherfucker in place. https://www.miataturbo.net/attachmen...at-housing-jpg Here is the rear section of the upper radiator hose. https://www.miataturbo.net/attachmen...upper-hose-jpg Here is the middle of upper hose. Highest point is below radiator cap height. Took a lot of test fitting and cutting to get it low enough. If I pulled the charcoal canister crap out it would have been easier. https://www.miataturbo.net/attachmen...upper-hose-jpg And finally the front blockoff and Radiator. You can also see the new lower hose. https://www.miataturbo.net/attachmen...koff-plate-jpg Next step is Fab 9 tuning coil on plug system. Looks like this will bethe easiest step in this build! Keith |
10 Attachment(s)
COP and power steering cooler are done. Pics
Here are the pencil coils installed. Plug gaps on the supplied plugs varried from .038 to .042, so I set them all down to .038 If I have spark blowout I will gap them down in increments until it goes away. https://www.miataturbo.net/attachmen...1&d=1409058975 Here is the plug and play connector, it is at the front passenger side on the NB1 cars. https://www.miataturbo.net/attachmen...1&d=1409058975 And here is the ignition module mocked up on the firewall. Didn't come with self tapping sheet metal screws, so I have to pick up some this morning to do the mounting. If I had some CPU heat transfer paste sitting around I would slather the heat transfer surface... but I don't and I am not going to order some just for this. https://www.miataturbo.net/attachmen...1&d=1409058975 Here is the BEGi power steering cooler mounted up front at the top of the opening in the bumper. https://www.miataturbo.net/attachmen...1&d=1409058975 And here in my opinion is the proper routing of the power steering lines for the BEGi power steering cooler. The stud that the rubberized clamp is mounted too is one of the mounting points for the fog lights, and the lines are running in the gap between the frame rail and the mounting point for the front sway bar. https://www.miataturbo.net/attachmen...1&d=1409058975 The last of the "fiddly bits" are the oil supply, and oil drain... then it is on to the meat and potatoes of the manifold, turbo, downpipe and intercooler. Any advice on reaching the oil supply point under the intake manifold? Looks like a real pain in the ass. Keith |
It is. Either jack the car up and remove the passenger wheel, or yank the alternator.
And of course there's always the option of yanking the IM. Its not too much more difficult than changing the oil filter though, just takes some shoving of hands through crevices that were designed for tiny japanese hands lol. |
|
Keith... i have a stupid question:
What sort of sorcery are you doing with your heater lines, and why? I have a Begi homebrew re-route to do, with the Escalade hose or whatever the hell, and i don't remember seeing anything about that "T" in the write ups i was looking at. |
All times are GMT -4. The time now is 12:08 AM. |
© 2024 MH Sub I, LLC dba Internet Brands