Any dyno numbers on this thing? Curious if so. Or at least throw a good 3rd gear pull into virtual dyno and see what you are at there. That would be neat. 13's isn't bad at all.
|
Yeah. Probably in the fall when it gets cooler out. I will probably also try to fine tune it.
Might try out this virtual dyno, i've never really looked into it. |
1 Attachment(s)
VD is a bit easier than i thought.
https://www.miataturbo.net/attachmen...ine=1343849912 Seems pretty dang low IMO. I'm going to go back out and try again after i make a few adjustments. Not sure why my AFR's were like they are when i went WOT around 2200rpm. Also, i'm not 200lbs, i just had crap in the car. :D Plus this was an up hill on ramp to an expressway, i'm guessing that would make a difference as well. |
3 Attachment(s)
I'll post this so you guys can pick me apart. I feel my AFR's go kinda funny until i am at desired boost level. Also, my boost level seems to spike then settle. Shitty boost controller i assume? Need to get EBC working.
https://www.miataturbo.net/attachmen...ine=1343861359 |
Looks like you got some boost drop here. Where's your wastegate signal coming from?
Also with virtual dyno make sure you do the pull on the flattest road possible, then cut out all extra data before you graph it. Also when graphing it make sure you have the correct final drive selected, and at least close to the correct tire height using their calculator. to break 13's i'd imagine you need to be at least 180whp, but I could be wrong. |
I'm pretty sure i have all the variables set correctly. I just had a bad "pull".
How would you crop what you wanted from the datalog? I've looked around a bit on megalogviewer but it's not very clear if you can do it with that. Hmm, i just found when reviewing this datalog that it's saying i lifted at 6600rpm, when i'm pretty sure my tachometer was at like 6900. I think the tach reads a little ligh, which would also explain why i don't bang the limiter i set at 6800 all the time. Anyone else experience this? |
nice build thread, been thumbing through it for a bit. on the virtual dyno question try removing some of the smoothness it will smooth the map to common points thus drop a few hp on the process. try like 2 instead of the 3 its set to in the pic
|
Yeah, bumped it to 184hp. Not much, but it's a few. Thanks for looking through.
|
Originally Posted by Erat
(Post 910523)
How would you crop what you wanted from the datalog? I've looked around a bit on megalogviewer but it's not very clear if you can do it with that.
I think the tach reads a little ligh, which would also explain why i don't bang the limiter i set at 6800 all the time. Anyone else experience this? |
Originally Posted by Fireindc
(Post 910514)
Looks like you got some boost drop here. Where's your wastegate signal coming from?
Also with virtual dyno make sure you do the pull on the flattest road possible, then cut out all extra data before you graph it. Also when graphing it make sure you have the correct final drive selected, and at least close to the correct tire height using their calculator. to break 13's i'd imagine you need to be at least 180whp, but I could be wrong.
Originally Posted by Monti
(Post 910656)
Look at the time index of your pull in megalogviewer and edit the file with a text editor of you choice, cutting all data bevor and after the pull. wordpad works fine!
Thats perfectly normal. Gonna do a little more work on it today, see what can't be done and post back. It's another hot day, here today 90F. |
Looking at your VD graph, you are on your way to 200whp if you didn't drop boost so drastically. What's your timing map look like? and where's that wastegate signal coming from? What is your wastegates pressure, and what pressure are you targeting?
|
1 Attachment(s)
Wastegate is coming off the compressor. I know that's not ideal, but usually you see pressure drop at high RPM's and i'm not getting that. It's an 8psi wastegate and i'm trying to hit 12psi. I'm really not dropping that much boost, it's a spike to about 14psi then settle at 12 very quickly.
https://www.miataturbo.net/attachmen...ine=1343936884 Looks a lot like your old spark map. I am pretty sure that this is untouched, and i'm not sure what to mess with on this. |
Ignition is hella conservative.
You could essentially shift that entire map up one cell. At 12 psi youre at 12.9 degrees atdc, you could easily be at 16 degrees. Also, move the wastegate signal to the cold side charge piping. Trust me. |
Originally Posted by Full_Tilt_Boogie
(Post 910769)
Ignition is hella conservative.
You could essentially shift that entire map up one cell. At 12 psi youre at 12.9 degrees atdc, you could easily be at 16 degrees. Also, move the wastegate signal to the cold side charge piping. Trust me. Timing map looks like it needs help, but I'm far from the one to give advise on that. |
Originally Posted by Full_Tilt_Boogie
(Post 910769)
Ignition is hella conservative.
You could essentially shift that entire map up one cell. At 12 psi youre at 12.9 degrees atdc, If he really was 12.9deg atdc it really would be ------- slow! |
2 Attachment(s)
Still have no idea what i'm doing with the MS...
But in the meantime. I put these wheels on. https://www.miataturbo.net/attachmen...ine=1344753145 They're meh. Not sure if i like them or not. I like my Boyds to much to like anything else. Picked up this hood the other day. I plan on cutting into it and putting some extractor vents in it. https://www.miataturbo.net/attachmen...ine=1344753145 Someone can make me an offer on either the hood or wheels, and if i like the price i'll sell both of them. |
1 Attachment(s)
Tweaked a few things, didn't touch spark. Went from 12psi to 10psi and got the numbers i'm more looking for.
https://www.miataturbo.net/attachmen...ine=1345300529 Graph cuts off at 6200rpm and i took it to 6400rpm according to the datalog. Not sure why VD did that. I hate how the tachometer is so slow, when i think i'm at 7000 i'm not. |
Dude add 3 degrees of timing everywhere above 100kpa and go make 15hp more.
Dann |
2 Attachment(s)
I didn't want to start a new thread for this.
But i have a question, on cold starts (ambient coolant temp) i usually have to cycle the ignition 3-4+ times after cranking before it actually fires. I've messed around with a few settings but i'm not sure which direction to go. Only ONCE have i had it backwire while doing this, which lead me to believe that it was cranking to lean. Was more like a spark cut pop out the exhaust. Coldest it's been was 60f and it was the worst. Even if i start it, drive it and let it sit for 4-6 hours then start it to drive it home that night it will start fine. Only when it sits overnight is when it gives me the problem. Otherwise it starts perfect. Tune is attached, i have some video if that helps. |
Is the 15:1 AFR between 2800 and 3400rpm something Erat should be worried about? or is it low enough that it doesnt matter?
|
All times are GMT -4. The time now is 02:39 PM. |
© 2024 MH Sub I, LLC dba Internet Brands