Anyone with coolant reroute done in RHD car?
 

I have been searching for Qmax coolent reroute or Begi, but not sure if either kit will fit on an RHD car. I see that the Clutch hydralic unit or brake booster could be in the way.

I did one recently that I went to the hot side wide enough to get past the turbo. I see no room on a right hand drive car to go to the cold side.

Thanks Olderguy, did you use an spacer for the rear Tstate?

Do you mind telling me how you have made the coolent reroute for the RHD car via Hotside?

Drilled out the capped-off water line to mount the ECU temp sensor at the back of the head.

Used the 1.6 thermostat cap with top plugged with a hose to 1" copper line with small "T" into heater core, continued 1" copper line past turbo on body shelf to modified 1.8 thermostat in front, then to radiator.

Hose from out of the heater core around hotside fender to modified connector at bottom radiator hose. Original hard line from heater core removed and entry to water pump for that line welded closed.

A reroute that cool and complex and there's no pictures. After spending all this time on the forum you do realize we're all visual learners right. Sounds slightly similar to mine I'll be doing.

I get too involved in the projects to take pictures until everything is working, then I don't want to disassemble all the later stuff to take the photos.

it all sounded like u need your head out! I am going direct to 949 on their Qmax!

Did it while the tranny was out, but could probably have done it with only the coils and CAS removed.

OG, I thought u would want water hot water flowing in the Heater core at all times even before the Tstate opens. From what you said, the T going into the heater core is after the Tstate.

Second, With the brake booster in the way, how was it drilling the Nibble plug to fit the rear T. Sensor?

Will it be possible to relocate the sensor at the front, instead of one sensor, put two?
http://http://i117.photobucket.com/a...r/DSC00199.jpg

Doesn't have real good pics but you should get the idea.
https://www.miataturbo.net/forum/showthread.php?t=14515
Or there are some more recent and better pics near the bottom of this page which give you a better idea.
http://mx5cartalk.com/viewtopic.php?t=29791

Tim

Thanks Tim, you had just about gave me all the confidence I need.

Do you think its possible to find a fitting YELLOW for the heater core? IS there enough room?

I don't think there would be enough room, and you would probably want the heater outlet to be pre-thermostat too both so it get hot water quicker and to have an alternate route for the water to relieve pressure from the pump while the thermostat is closed.

You can always change the front outlet to the 1.8 one and shift the stock heater oulet and thermoswitch to the front of the motor without having to get a new outlet made specifically.

Tim

For faster heating you want your heater hose after the thermostat. It lets the water warm up in the motor and then releases it.
I know when I take thermostats out for cooling issues the heater sucks. When winter hits, I buy one quick. It takes forever to warm up.

The factory setup has the heater outlet before the thermostat.

So.. the question now!

Heater Core water supply should be taken BEFORE or AFTER the Tstat?

BEFORE

You want circulation through the entire engine before the t/stat opens.

If you cut the "bung" section off. That half inch or so of extra aluminum you might be able to retap the fixture or have something welded onto that to do the same thing.

Any reason why when i do my reroute i can't eliminate the hardline under the manifold for the heater inlet. Then instead get my heater inlet from a fitting in my spacer before the thermostat then letting the heater core dump back into the system on the otherside of the thermostat like mimime showed with that 90* on the outside of that thermostat outlet? You would have really short lines, the thermostat would see the warm coolant from the engine on both sides, and the heatercore would still be bypassing coolant for some preflow before the thermo opened completely.

Cjernigan, can you document yours with a powerpoint? :bowrofl:

I can take a few pictures. There are tons of pictures on the forum of other people reroutes though. Just have to find them.

Anyone know where I can buy the JR spacer? From MOSS site this part 051-046 is not found.