Budget Build Ideas?
#1
Budget Build Ideas?
So badicaly I am 18 years old and in my senior year of high school. I somehow managed to pick up a MINT 2000 Miata LS with 46k miles for $5,000 over the summer.
I figured before I go off to college I go out with a bang. During summer break I plan on going turbo. This is 100% funded by me so budget and reliability are my main concerns. I don't want a drag sleeper beast miata. I just need a little more pep.
Here is my idea:
MK turbo kit & oil like kit
new injectors
cx racing intercooler
ebat bov
some cheap wideband and boost gauge
clutch (would probably wait until my current slips)
for an ecu I was considering either buying a used ms2 or getting the diy ms3 kit as I do have experience soldering
Obviously I have lots of research left to do and a long time until any part is ordered, but I just wanted to know what you guys think. I'm looking for 200whp. Do you think it could be done reliably for ~$3000-$3500?
I figured before I go off to college I go out with a bang. During summer break I plan on going turbo. This is 100% funded by me so budget and reliability are my main concerns. I don't want a drag sleeper beast miata. I just need a little more pep.
Here is my idea:
MK turbo kit & oil like kit
new injectors
cx racing intercooler
ebat bov
some cheap wideband and boost gauge
clutch (would probably wait until my current slips)
for an ecu I was considering either buying a used ms2 or getting the diy ms3 kit as I do have experience soldering
Obviously I have lots of research left to do and a long time until any part is ordered, but I just wanted to know what you guys think. I'm looking for 200whp. Do you think it could be done reliably for ~$3000-$3500?
#4
Elite Member
iTrader: (5)
Join Date: Oct 2011
Location: Detroit (the part with no rules or laws)
Posts: 5,677
Total Cats: 800
Man, i would hate to build this all summer than slip the clutch before it exits the driveway.
Edit* I was smart though. I used my extra college loan money to build my car. thatinterestratetho
Edit* I was smart though. I used my extra college loan money to build my car. thatinterestratetho
Last edited by Erat; 11-21-2016 at 08:53 PM.
#5
You should probably add money else where assuming its a bone stock car. A nice set of fm or megan coils will be "better than stock" without breaking the bank. Then look into getting a new set of rubber and maybe a roll bar and enjoy life. I'm still in high school and I'll admit that I've failed many times on my build, I would NOT turbo it as your only mode of transportation, my car has left me stranded more than once. Some one on here said that the key to making a reliable turbo miata is to get it to work good enough and then stop ******* with it. Don't let me scare you though, just be weary of what your getting into.
#9
Elite Member
iTrader: (1)
Join Date: Mar 2014
Location: Jacksonville, FL
Posts: 1,552
Total Cats: 196
the clutch on my NB is good for 220hp, and around 12psi. after that it slips. no idea what kind of clutch is in there, i am assuming original or oem replacement 180k miles on car.
so for his 200hp goal, the current clutch might hold just fine.
I also have a 99-00 mslabs MS2 enhanced for sale if you are interested. 6 months old, works perfectly.
so for his 200hp goal, the current clutch might hold just fine.
I also have a 99-00 mslabs MS2 enhanced for sale if you are interested. 6 months old, works perfectly.
#10
mkturbo.com
iTrader: (24)
Join Date: May 2006
Location: Charleston SC
Posts: 15,177
Total Cats: 1,681
the clutch on my NB is good for 220hp, and around 12psi. after that it slips. no idea what kind of clutch is in there, i am assuming original or oem replacement 180k miles on car.
so for his 200hp goal, the current clutch might hold just fine.
I also have a 99-00 mslabs MS2 enhanced for sale if you are interested. 6 months old, works perfectly.
so for his 200hp goal, the current clutch might hold just fine.
I also have a 99-00 mslabs MS2 enhanced for sale if you are interested. 6 months old, works perfectly.
Overall OP your its sounds pretty good. You just need to work on the order of it all. Follow these steps to win.
1. MS and Wideband. MS3 is what you want to go with. For the woodbine Innovative or AEM. Install these on the bone stock car and learn to tune.
2. FlowForce injectors. Get these and install them and retune fuel and such.
3. Clutch. FM, ACT, 949Racing are the only brands you should be looking at.
4. Intercooler setup, get this figured out before you add turbo hardware. Cold side piping and IC can be mounted while naturally aspirated, then just have to worry about the hot side parts once you have your turbo stuff.
5. Turbo hardware. MKTurbo/Fm/TSE/Artech/Begi are where you should be looking.
#11
Elite Member
iTrader: (1)
Join Date: Mar 2014
Location: Jacksonville, FL
Posts: 1,552
Total Cats: 196
I also happen to have all that you need in your list for sale.
https://www.miataturbo.net/miata-par...xh-more-91286/
https://www.miataturbo.net/miata-par...xh-more-91286/
#12
Elite Member
iTrader: (2)
Join Date: Aug 2016
Location: New Fucking Jersey
Posts: 3,890
Total Cats: 143
Borka, you might have an aftermarket clutch on there. How many miles did the car have when you got it?
Are you suggesting running the car NA with an intercooler or just mounting everything and mocking up the piping?
Thanks!
You are lucky on your clutch. My stock 1.8 clutch started slipping between 4-6psi.
Overall OP your its sounds pretty good. You just need to work on the order of it all. Follow these steps to win.
1. MS and Wideband. MS3 is what you want to go with. For the woodbine Innovative or AEM. Install these on the bone stock car and learn to tune.
2. FlowForce injectors. Get these and install them and retune fuel and such.
3. Clutch. FM, ACT, 949Racing are the only brands you should be looking at.
4. Intercooler setup, get this figured out before you add turbo hardware. Cold side piping and IC can be mounted while naturally aspirated, then just have to worry about the hot side parts once you have your turbo stuff.
5. Turbo hardware. MKTurbo/Fm/TSE/Artech/Begi are where you should be looking.
Overall OP your its sounds pretty good. You just need to work on the order of it all. Follow these steps to win.
1. MS and Wideband. MS3 is what you want to go with. For the woodbine Innovative or AEM. Install these on the bone stock car and learn to tune.
2. FlowForce injectors. Get these and install them and retune fuel and such.
3. Clutch. FM, ACT, 949Racing are the only brands you should be looking at.
4. Intercooler setup, get this figured out before you add turbo hardware. Cold side piping and IC can be mounted while naturally aspirated, then just have to worry about the hot side parts once you have your turbo stuff.
5. Turbo hardware. MKTurbo/Fm/TSE/Artech/Begi are where you should be looking.
Thanks!
#13
mkturbo.com
iTrader: (24)
Join Date: May 2006
Location: Charleston SC
Posts: 15,177
Total Cats: 1,681
Depends on how early you decide to mock up stuff. There is no reason you can't run the cold side pipes, and IC, and then put a filter on the other side of the IC. Won't help with cooling of air or anything, but will make the day where you install everything else a bit easier. I wouldn't suggest doing this like 6+ months before the other turbo hardware.
#14
Elite Member
iTrader: (2)
Join Date: Aug 2016
Location: New Fucking Jersey
Posts: 3,890
Total Cats: 143
Depends on how early you decide to mock up stuff. There is no reason you can't run the cold side pipes, and IC, and then put a filter on the other side of the IC. Won't help with cooling of air or anything, but will make the day where you install everything else a bit easier. I wouldn't suggest doing this like 6+ months before the other turbo hardware.
Thanks man!
#16
I built my first turbo setup in the same time frame. Really helps if you can weld or fabricate at all. I took a welding class at the local community college and learned a great deal. The machinist instructor was super supportive and let me use his shop when the course ended. Drove the car all through college (commuted ~50 miles a day). Sometimes I miss the stupid simpleness of the FM voodoo box and small turbo on a few psi. Car was my daily its totally do able but I spent the vast majority of my time tinkering on it. Pulling the header off, test fitting, putting it all back together to go somewhere, etc.
Thread
Thread Starter
Forum
Replies
Last Post
borka
Miata parts for sale/trade
23
12-28-2016 11:24 PM