Originally Posted by samwu8k
(Post 900179)
aww man i dont wanna melt stuff and have fitment issues.
how can u guys tell its not sc40 pipe? is it cuz it comes with that cast look on the surface compared to the smooth finish on the piping they used? You also need to make sure they used a TiAL v-band flange and welded on a male-side rather than a female. |
So, does the hood close with that setup? Looks really close.
|
Its funny because their "proven 900whp manifolds" dont list ---- about the actual piping.... Pipe diameter, pipe thickness.. no usefull info at all. And their flange looks like they cut it on a bandsaw without even facing it... and at last 795 with 60 bucks shipping.
|
i like how it only made 200rwhp.
it's a shitty design; the placement is horrible. this made me laugh: We started this build by selecting a properly sized turbo and a DOC Race turbo manifold. ... Precision PT5557 Turbo |
Originally Posted by fwMiata
(Post 900225)
So, does the hood close with that setup? Looks really close.
206/171 is pretty weak though. Did they tune it for 4-5psi? I like the placement design only because it keeps everything away from the heater hoses and master cylinder. Looks like it should have some supporting though. |
So instead of melting heater hoses and boiling brake fluid, you're melting power steering, ac, and lower rad hoses, and boiling ps fluid.
PHAIL |
Originally Posted by 18psi
(Post 900329)
So instead of melting heater hoses and boiling brake fluid, you're melting power steering, ac, and lower rad hoses, and boiling ps fluid.
PHAIL It says not compatible with power steering. :vash: |
---- that manifold.
Miatas are now the new "baller" car to buy and slam and do stupid ---- with, which means we will see lots of stupid ---- ---- like this. I ------- hate this ----, all these retards have to ---- up all the best ------- cars to play with so all the cars and engines and parts get torn up and expensive. Fills me with hate. |
Originally Posted by Full_Tilt_Boogie
(Post 900357)
---- that manifold.
Miatas are now the new "baller" car to buy and slam and do stupid ---- with, which means we will see lots of stupid ---- ---- like this. I ------- hate this ----, all these retards have to ---- up all the best ------- cars to play with so all the cars and engines and parts get torn up and expensive. Fills me with hate. |
someone on here needs to buy one and test for us
|
I'm sure you can trick some one on CR.
|
Originally Posted by triple88a
(Post 900355)
Man u been spending too much time with Fae.
It says not compatible with power steering. :vash: either way, you're right next to the lower rad hose (unless you re-locate) and even more crowded toward the front for no apparent reason: its not bottom mount for optimal downpipe routing. its not side-mount for more compact-ness, and its not top mount to retain p/s. its like the worst of everything. someone please explain to me the advantages of that placement aside from " EET LEWKS KEEWL DAWGGG" |
Originally Posted by pusha
(Post 900365)
someone on here needs to buy one and test for us
i went trough their website and they got some really nice cars coming trough their shop, they might not be miata experts but they arent noobz either. they tuned the car to 200 hp as a break in or something and claimed it should push somewhere in the 300s with a good tune. the turbo itself is capable, i doubt the stock motor could sustain that power level for long. although this manifold might not be the optimal design wastegate wise it reminds me of the full race-manifolds for s2k and those look sick as well. ive also noticed alot of turbo manifolds for honda k-series engines usually hang the turbo wayy off to the side of the engine bay with some pretty long runners. seems like they are completely unbraced as well. but then again im just ur avg ricer so perhaps idk what im lookin @ |
Originally Posted by samwu8k
(Post 900487)
they tuned the car to 200 hp as a break in or something and claimed it should push somewhere in the 300s with a good tune. the turbo itself is capable, i doubt the stock motor could sustain that power level for long.
when the last time you needed a boost break-in? |
Originally Posted by 18psi
(Post 900329)
So instead of melting heater hoses and boiling brake fluid, you're melting power steering, ac, and lower rad hoses, and boiling ps fluid.
PHAIL I don't have PS or AC, so that didn't cross my mind. IMO, the lower rad hose is easier to shield or cover than the tight radius heater hoses. |
Originally Posted by Vashthestampede
(Post 900518)
lol
I don't have PS or AC, so that didn't cross my mind. IMO, the lower rad hose is easier to shield or cover than the tight radius heater hoses. ARtech can make you a bad mutha fugga twin scroll sex manifold for that price. |
2 Attachment(s)
Pics from a guy on the MT facebook page (not the legit OG chat)
https://www.miataturbo.net/attachmen...ine=1343372108 http://sphotos-a.xx.fbcdn.net/hphoto...66680412_n.jpg Manifold is not compatible with headlight motors... https://www.miataturbo.net/attachmen...ine=1343372108 |
I can smell the heater core return line melting from here. Do you suppose they could clock the air intake down 30* so it could be completely behind the radiator? That way you could get very consistent IAT in the 200* range. :facepalm:
|
i like the flimsy brace, that will crack within a few hours.
|
2 Attachment(s)
Originally Posted by Braineack
(Post 908588)
i like the flimsy brace, that will crack within a few hours.
Brain called it. Anyone else wanna argue for sch.10 stainless manifolds?????
Originally Posted by MT facebook guy
Cracked dead center of the weld and they still wouldn't swap it out. Only would they repair it and this is my dd.
I asked them if they purge the Manu with Argon while the weld it and they said no. Lol I highly don't recommend DOC RACING! https://www.miataturbo.net/attachmen...ine=1343400284 Yo, OP. Get your faggette-asss back in here and tell us how you want this thing because it's "menacing looking". |
All times are GMT -4. The time now is 02:46 AM. |
© 2024 MH Sub I, LLC dba Internet Brands