YeboGoGo

iTrader: (1)

I swear that nothing has made me feel bipolar as much as this project!

I have owned a diypnp for 2 years and various turbos for at least one. Any time I have started to make progress I start to think maybe I should swap the motor. Well this past weekend after a ton of bs issues I decided to say f it and turbo. First step was the Megasquirt.

Since my wiring harness has gone on a diet I was concerned that maybe some wires would be needed but it appeared to be ok

While adding another O2 bung to get my MS skills up I laid a Subaru turbo in place. Looks like I have plenty of room.
Sadly I feel like this turbo is too small so I'm going to throw it up for sale and look for a BG one.

Here is the first picture. Planning to make my own log manifold as most others don't fit this chassis

Turbo in place
The inside wiring situation
more to come...

jonbmet

Man that thing is awesome. Let me know if you ever need a hand!

rx7_guy

Bad boy looks like it will be fast

DNMakinson

iTrader: (3)

Power goals? Stock engine? What year is engine? '97 IIRC.

YeboGoGo

iTrader: (1)

I don't really have a goal. Is "a lot" a goal? Ultimately 300+ but since I haven't driven an 1100 lb car with more than 115 HP it becomes hard to say. 200 might be enough!

Engine is stock now. 94 engine.

Basically I plan to get another block and add rods and pistons.
Still debating the turbo and then I have the problem of trying to cram it all in and keep the heat down so my legs don't burn

DNMakinson

iTrader: (3)

TD04 would be more than adequate for 200WHP; and on stock engine.

You have to figure out how you are going to figure out.

Seems like <5# per HP should be enough. cars 5# per HP

jaf1901

I'm in the same boat as you...........although I've just been driving around with the wastegate open.
I plan to start building boost shortly. I'll tell you that combating the heat is a serious issue.

YeboGoGo

iTrader: (1)

thats a clean car!! My steering shaft runs through the area you used. Do you have any more pictures of the manifold and IC setup?


My main goal is to have a turbo frame that can have the body upgraded. I'm hoping not to have to change flanges etc at a later date..
That's my biggest concern on the td04. I thought perhaps about the vf39 or one of the Borg Warner efr's

DNMakinson

iTrader: (3)

Standard Garrett or BW is a big advantage for upgrading, from what I understand.

jaf1901

No intercooler yet.....but more than enough room to incorporate as I turn up the boost. You can check out my build over on the Locost Forum........here:
LocostUSA.com ? View topic - JAF's +221-Haynes/Custom-Miata

YeboGoGo

iTrader: (1)

Well it might be time to try another wideband even though my aem has less than an hour on it..

Plugged the gauge into my db9 port and the af numbers are the same as I saw in studio tuner.... Which is different to the gauge face..

I've changed the ground wire.. Anyone have any other ideas?

sharkythesharkdogg

Neat set-up, but I have to ask. Why'd you keep the ancient AFM?

YeboGoGo

iTrader: (1)

Ahhhh victory today! After trying everything imaginable I got a tip to disconnect the wideband o2 sensor and should see 14.7 as a constant. Gauge showed it but megasquirt was at 12.

After trying every very ground I could it didn't get better. I got frustrated.

Then I had a thought that it could be the stock o2 sensor.I walked over and unplugged it and perfect!!

short version- disconnect the stock o2 sensor.

going to try tune it tomorrow. Wish me luck