Miata Turbo Forum - Boost cars, acquire cats.
0 2024/12/24 20:18:35
Last time you'll see this setup
Last time you'll see this setup
0 2024/12/24 20:18:32
0 2024/12/20 12:46:27
0 2024/12/20 12:40:01
0 2024/12/20 12:39:18
0 2024/12/24 20:22:44
0 2024/12/20 12:39:14
0 2024/12/20 12:38:44
0 2024/12/20 12:35:31
0 2024/12/20 12:26:13
0 2024/12/20 12:26:10
0 2024/12/20 12:26:06
0 2024/12/20 12:26:01
At this point the nut was locked onto the stud and rounding off, but not fully seated on the elbow.
At this point the nut was locked onto the stud and rounding off, but not fully seated on the elbow.
0 2024/12/25 20:57:38
0 2024/12/17 12:30:26
0 2024/12/17 12:30:21
0 2024/12/17 12:30:18
0 2024/12/25 21:06:50
I haven't confirmed that these mate up with the header on the G4x yet, but they look identical and I believe they are the correct part number.
I haven't confirmed that these mate up with the header on the G4x yet, but they look identical and I believe they are the correct part number.
0 2024/12/16 09:15:24
0 2024/12/16 09:02:43
0 2024/12/16 09:02:39
Coldside is just a bit tight near the AC lines. Not too bad, but I'd rather not wear a hole in the aluminum.
Coldside is just a bit tight near the AC lines. Not too bad, but I'd rather not wear a hole in the aluminum.
0 2024/12/25 21:14:59
These are the injector seal kits I used. No leaks so far
These are the injector seal kits I used. No leaks so far
0 2024/12/16 09:02:34
The "6" is a dryer vent
The "6" is a dryer vent
0 2024/12/13 10:40:14
0 2024/12/13 08:46:28
Grime buildup from being coated in oil
Grime buildup from being coated in oil
0 2024/12/11 20:34:21
Bottom Cushion on the left. Spooly boi on the right?
Bottom Cushion on the left. Spooly boi on the right?
0 2024/12/11 20:29:36
0 2024/12/11 20:29:32
Check valve in case the solenoid failed open somehow. Don't want to pressurize the fuel tank.
Check valve in case the solenoid failed open somehow. Don't want to pressurize the fuel tank.
0 2024/12/11 20:27:28
0 2024/12/26 13:32:28
Got the TV for free from a friend. Ended up a bit lower than I wanted, but I can always change that later if I really want to. It's mostly background noise anyway
Got the TV for free from a friend. Ended up a bit lower than I wanted, but I can always change that later if I really want to. It's mostly background noise anyway
0 2024/12/11 20:24:13
0 2024/12/11 20:22:25
Barely fits with the actual coil
Barely fits with the actual coil
0 2024/12/11 20:16:11
Filling in this gap will keep the seal sitting flush with the plug hole.
Filling in this gap will keep the seal sitting flush with the plug hole.
0 2024/12/31 17:35:28
Fits so well
Fits so well
0 2024/12/11 20:16:08
0 2024/12/09 10:45:52
0 2024/12/31 17:36:34
Way more exposed threads than my old setup.
Way more exposed threads than my old setup.
0 2025/01/20 21:16:29
Way more threads are exposed than on my old setup.
Way more threads are exposed than on my old setup.
0 2025/01/20 21:15:43
0 2025/01/16 20:11:02