Miata Turbo Forum - Boost cars, acquire cats.
0 2024/06/25 08:32:23
0 2024/06/25 08:32:28
0 2024/06/25 08:32:33
0 2024/07/01 10:30:12
0 2024/07/01 10:30:16
0 2024/07/01 10:30:20
2560 with a generic MAC boost control solenoid
2560 with a generic MAC boost control solenoid
0 2024/07/03 12:14:47
0 2024/07/03 12:19:47
1/8 E clip from home depot works on the top latch pin. A bit tight, but the next largest size was too big.
1/8 E clip from home depot works on the top latch pin. A bit tight, but the next largest size was too big.
0 2024/07/03 12:19:52
0 2024/07/03 12:33:10
0 2024/07/10 20:05:56
I remember this looking better when I first did it.
I remember this looking better when I first did it.
0 2024/07/10 20:06:00
0 2024/07/10 20:08:07
0 2024/07/10 20:08:12
The curly q is to try to prevent any potential liquid from splashing out freely.
The curly q is to try to prevent any potential liquid from splashing out freely.
0 2024/07/10 20:26:42
0 2024/07/11 09:48:29
Tape lined up by eye. I drilled small holes in the corners before cutting.
Tape lined up by eye. I drilled small holes in the corners before cutting.
0 2024/07/15 09:17:57
Long needle nose pliers worked well to bend the tabs. Bend these down before cutting the next one or the hood just flexes instead of bending.
Long needle nose pliers worked well to bend the tabs. Bend these down before cutting the next one or the hood just flexes instead of bending.
0 2024/07/15 09:18:02
End result
End result
0 2024/07/15 09:18:07
I would recommend taking the hood off for best results. I was on a time crunch and my heart wasn't into it.
I would recommend taking the hood off for best results. I was on a time crunch and my heart wasn't into it.
0 2024/07/15 09:18:14
0 2024/07/15 09:18:19
0 2024/07/15 09:27:34
0 2024/07/15 09:49:55
0 2024/07/15 09:56:23
0 2024/07/15 15:58:59
0 2024/07/16 12:30:10
0 2024/07/18 13:49:41
0 2024/07/23 10:48:48
This has been modified slightly since this photo was taken.
This has been modified slightly since this photo was taken.
0 2024/07/24 12:11:25
0 2024/07/25 08:19:51
This is where the piston skirt was contacting the rod
This is where the piston skirt was contacting the rod
0 2024/07/25 08:19:55
I have to assume the other 3 rods are in similar condition.
I have to assume the other 3 rods are in similar condition.
0 2024/07/25 08:19:58
Rod, cap and the bearings that were installed when it was pulled from the engine.
Rod, cap and the bearings that were installed when it was pulled from the engine.
0 2024/07/25 08:20:02
After a light wipe with a rag.
After a light wipe with a rag.
0 2024/07/25 08:20:06
0 2024/08/07 09:20:55
0 2024/08/07 09:20:50
0 2024/08/07 09:25:21
0 2024/08/08 08:28:43
0 2024/08/08 08:34:39
0 2024/08/08 08:35:38