Miata Turbo Forum - Boost cars, acquire cats.
021
021
0 2012/04/06 14:57:42
038 old tired msm motor, coming out to get "refreshed".
038 old tired msm motor, coming out to get "refreshed".
0 2012/04/06 14:57:42
047 corbeau pro-x1 seats are a tight fit, but they do work with minimal clearancing. Narrow, so I'd better not gain any weight.
047 corbeau pro-x1 seats are a tight fit, but they do work with minimal clearancing. Narrow, so I'd better not gain any weight.
0 2012/04/11 08:33:23
055 master cut off switch fit nicely in the gutted out dash pad
055 master cut off switch fit nicely in the gutted out dash pad
0 2012/04/11 08:33:23
042 seat mounts built up in front and just a bolt thru the floor pan for the rear mounts.
042 seat mounts built up in front and just a bolt thru the floor pan for the rear mounts.
0 2012/04/11 08:33:23
051 The harness installation was a royal pain as the Corbeau camlock didn't fit thru the Corbeau side-seat slot. This meant that you had to thread the belt thru the seat and weave/secure the belt to the mount while the seat was in the way.
051 The harness installation was a royal pain as the Corbeau camlock didn't fit thru the Corbeau side-seat slot. This meant that you had to thread the belt thru the seat and weave/secure the belt to the mount while the seat was in the way.
0 2012/04/11 08:38:08
049
049
0 2012/04/11 08:38:08
056 manual boost controller installed in the cigarette lighter slot.
056 manual boost controller installed in the cigarette lighter slot.
0 2012/04/11 08:38:08
018 an e-bay rx7 oil cooler. Will need to source out a couple of 16mm x 1.5 straight thread -8 90 degree adapters to make this work. Still I may have to tip the radiator back some; or merely run the lines out the front side. Still a work in progress.
018 an e-bay rx7 oil cooler. Will need to source out a couple of 16mm x 1.5 straight thread -8 90 degree adapters to make this work. Still I may have to tip the radiator back some; or merely run the lines out the front side. Still a work in progress.
0 2012/04/30 09:23:14
022 Oil cooler from the front. Also working on a front mounted intake; using the frame rail as the duct. First a trial for fittment, as the bumper cover is a close fit. Then I'll gut and gusset the frame tube.
022 Oil cooler from the front. Also working on a front mounted intake; using the frame rail as the duct. First a trial for fittment, as the bumper cover is a close fit. Then I'll gut and gusset the frame tube.
0 2012/04/30 09:23:14
031 Everything fits!
031 Everything fits!
0 2012/04/30 09:23:14
012 225-45-15's next to my OEM 205-40-17's
012 225-45-15's next to my OEM 205-40-17's
0 2012/05/18 08:32:31
017
017
0 2012/05/30 13:29:01
019
019
0 2012/05/30 13:29:01
031
031
0 2012/05/30 13:29:01
028 radiator air ducting: sealed in the nose using sheet aluminum
028 radiator air ducting: sealed in the nose using sheet aluminum
0 2012/06/22 08:26:19
029 radiator air ducting from the side which seals around the intercooler piping and is continuous with the factory plastic tray
029 radiator air ducting from the side which seals around the intercooler piping and is continuous with the factory plastic tray
0 2012/06/22 08:26:19
027 bedded in the radiator bottom with spray foam. spray it on and then set the radiator into it, and let dry.
027 bedded in the radiator bottom with spray foam. spray it on and then set the radiator into it, and let dry.
0 2012/06/22 08:26:19
034 radiator ducting: tape off the upper radiator and installed a filler plate from BEIG.
034 radiator ducting: tape off the upper radiator and installed a filler plate from BEIG.
1 2012/06/22 08:31:57
031 radiator ducting: add a small splitter to help direct air in from the bottom
031 radiator ducting: add a small splitter to help direct air in from the bottom
0 2012/06/22 08:31:57
029 new brakes and ducts installed
029 new brakes and ducts installed
0 2012/08/03 11:26:46
0 2012/08/03 11:26:46
the oem diff bushings can be split along their parting line when removing to install poly.
the oem diff bushings can be split along their parting line when removing to install poly.
0 2012/08/13 16:48:38
030
030
0 2012/08/20 08:53:39
did those manifold crimp nuts really rattle loose in one 30 min session?
did those manifold crimp nuts really rattle loose in one 30 min session?
0 2012/08/20 08:53:39
specmiata The old standby SM #2. Reliable and lot's of fun, even in the rain.
specmiata The old standby SM #2. Reliable and lot's of fun, even in the rain.
0 2012/08/20 09:56:03
Johnson File4
Johnson File4
0 2012/10/22 08:16:50
Johnson File5 conservative boost levels and a little fat on the AFR's will keep the motor alive for many seasons!
Johnson File5 conservative boost levels and a little fat on the AFR's will keep the motor alive for many seasons!
0 2012/10/22 08:16:50
oldcomputerpics 524
oldcomputerpics 524
0 2012/10/29 11:56:27
oldcomputerpics 519
oldcomputerpics 519
0 2012/10/29 11:56:27
oldcomputerpics 563
oldcomputerpics 563
0 2013/01/09 13:05:42
056
056
0 2013/04/29 12:13:27
045
045
0 2013/05/06 10:53:33
046
046
0 2013/05/06 10:53:33
071
071
0 2013/05/15 08:02:53
070
070
0 2013/05/15 08:02:53
111
111
0 2013/05/15 14:33:53
054
054
0 2013/05/23 16:58:28
058
058
0 2013/05/23 16:58:28