Miata Turbo Forum - Boost cars, acquire cats.
0 2016/12/11 16:37:31
0 2016/12/05 17:57:42
0 2016/12/04 09:52:41
0 2016/12/04 09:52:03
0 2016/12/01 21:00:14
Again, on the backside. This really deadened the plate with not a lot of surface coverage.
Again, on the backside. This really deadened the plate with not a lot of surface coverage.
0 2016/11/29 18:54:52
Spot on side of tunnel
Spot on side of tunnel
0 2016/11/29 18:54:51
Placing in on the backside cause, why not?
Placing in on the backside cause, why not?
0 2016/11/29 18:54:50
I could take some or all of the divider out.
I could take some or all of the divider out.
0 2016/11/29 18:49:52
Seems like some porting of the WG path could yield some positive result.
Seems like some porting of the WG path could yield some positive result.
0 2016/11/29 18:49:51
It would seem to me, that if I did pull the divider out of the exit housing, then I might as well delete the segregated dump tube and simplify the downpipe.
It would seem to me, that if I did pull the divider out of the exit housing, then I might as well delete the segregated dump tube and simplify the downpipe.
0 2016/11/29 18:49:50
0 2016/11/29 18:49:15
With WG wired open.
With WG wired open.
0 2016/11/28 18:32:28
Using a 7.5psi wastegate.
Using a 7.5psi wastegate.
0 2016/11/28 18:32:27
Picture of wastegate wired open.
Picture of wastegate wired open.
0 2016/11/28 18:32:25
start-up using "2" in filter, instead of "4". I did not run this way yet. Just started it.
start-up using "2" in filter, instead of "4". I did not run this way yet. Just started it.
0 2016/11/14 09:14:08
2nd sync loss, same log
2nd sync loss, same log
0 2016/11/14 09:13:42
Sync loss, but WHY? triggers look correct
Sync loss, but WHY? triggers look correct
0 2016/11/14 09:13:10
Crank switching from down-up to up-down
Crank switching from down-up to up-down
0 2016/11/14 09:12:32
Sometimes I see this. Cam has no lines but does have the yellow dots. No sync loss
Sometimes I see this. Cam has no lines but does have the yellow dots. No sync loss
0 2016/11/14 09:11:47
Typical Section running. I expected the Crank to be Down-Up like the Cam
Typical Section running. I expected the Crank to be Down-Up like the Cam
0 2016/11/14 09:10:05
Typical Pattern
Typical Pattern
0 2016/11/14 09:06:46
Sync loss, but WHY. Signals look OK
Sync loss, but WHY. Signals look OK
0 2016/11/14 09:06:45
Crank switching from down-up to up-down
Crank switching from down-up to up-down
0 2016/11/14 09:06:45
Start with filtering at "2" instead of "4"
Start with filtering at "2" instead of "4"
0 2016/11/14 09:06:44
No lines on Cam, just yellow dots
No lines on Cam, just yellow dots
0 2016/11/14 09:06:44
2nd sync loss, same log
2nd sync loss, same log
0 2016/11/14 09:06:43
Crank with
Crank with
0 2016/11/14 09:05:22
cranking with HDW filter at "2" rather than "4"
cranking with HDW filter at "2" rather than "4"
0 2016/11/14 09:04:21
2nd sync loss on same log
2nd sync loss on same log
0 2016/11/14 09:03:55
Sync loss shown, But WHY? Signals look OK.
Sync loss shown, But WHY? Signals look OK.
0 2016/11/14 09:03:03
Crank switching from down up, to up down.
Crank switching from down up, to up down.
0 2016/11/14 09:02:17
Typical with seeming upside down Crank
Typical with seeming upside down Crank
0 2016/11/14 09:01:36
0 2016/11/09 08:48:01
0 2016/11/08 15:38:03
0 2016/11/08 15:38:02
Water connection at mixing manifold
Water connection at mixing manifold
0 2016/11/08 15:35:48
Side view of hard lines
Side view of hard lines
0 2016/11/08 15:35:47
0 2016/11/08 14:53:14
0 2016/11/03 11:42:32