Miata Turbo Forum - Boost cars, acquire cats.
0 2023/08/19 13:50:24
0 2023/08/14 08:05:23
No Oil Pressure Present
No Oil Pressure Present
0 2023/05/18 13:52:27
Oil Pressure Present
Oil Pressure Present
0 2023/05/18 13:52:25
Windings and shaft removed, not drilled out yet. I filled the cavity and glued the 2 bobbin halves back together with Ultem Hot Melt, before drilling.
Windings and shaft removed, not drilled out yet. I filled the cavity and glued the 2 bobbin halves back together with Ultem Hot Melt, before drilling.
0 2023/05/18 13:18:07
0 2023/05/18 13:18:05
Where I put the un-needed relay
Where I put the un-needed relay
0 2023/05/18 13:18:03
0 2023/05/18 13:16:59
0 2023/01/31 04:51:50
0 2023/01/07 16:32:28
0 2022/12/15 06:49:24
0 2022/10/29 17:22:48
0 2022/10/29 17:22:37
0 2022/10/10 11:24:24
0 2022/09/12 14:36:31
0 2022/09/04 14:34:52
0 2022/08/09 09:42:24
0 2022/07/29 14:59:26
0 2022/04/16 15:30:33
I'm not sure about this, as the instructions do not mention the "Fixed" setting.
I'm not sure about this, as the instructions do not mention the "Fixed" setting.
0 2022/01/19 07:44:47
What you have, which seems to have the Baro directly in the fueling equation.
What you have, which seems to have the Baro directly in the fueling equation.
0 2022/01/19 07:44:44
0 2021/11/06 10:15:35
0 2021/09/11 05:33:53
My Table to my upper values, but with Andy's interpolation rows and columns.
My Table to my upper values, but with Andy's interpolation rows and columns.
0 2021/08/24 17:18:20
Andy's Table Spanning only to 18 psi (my upper limit) Compare to the next picture, which is my table Interpolated with the same rows and columns as this one (cell to cell correlation).
Andy's Table Spanning only to 18 psi (my upper limit) Compare to the next picture, which is my table Interpolated with the same rows and columns as this one (cell to cell correlation).
0 2021/08/24 17:18:12
Andy's 93 octane Table set up to 21psi
Andy's 93 octane Table set up to 21psi
0 2021/08/24 17:18:04
My Actual Table
My Actual Table
0 2021/08/24 17:17:53
0 2021/07/17 03:56:15
0 2021/07/17 03:55:04
0 2021/06/07 15:42:34
0 2021/06/07 15:41:23
Finished Product
Finished Product
0 2021/05/18 16:39:29
Looking down. Swing arm that pulls the cable is just in front of the seat.
Looking down. Swing arm that pulls the cable is just in front of the seat.
0 2021/05/18 16:25:55
This does not really show that guide is too low, but it is. Seat cannot go all the way back to the wall. I don't need it to, as back is so thin, but a 6' + guy might want it back more.
This does not really show that guide is too low, but it is. Seat cannot go all the way back to the wall. I don't need it to, as back is so thin, but a 6' + guy might want it back more.
0 2021/05/18 16:25:54
Seat belt guide on roll bar is a little low and outboard. I will likely move it with a bracket to line up better. This is with seatback at same 20* angle as the back wall.
Seat belt guide on roll bar is a little low and outboard. I will likely move it with a bracket to line up better. This is with seatback at same 20* angle as the back wall.
0 2021/05/18 16:25:53
Side view
Side view
0 2021/05/18 16:25:52
Finished installation
Finished installation
0 2021/05/18 16:25:50
Finished sliders with side brackets and front rail. Kept all the OEM belt safety features. As set up a couple of posts up, for no rear hump mount.
Finished sliders with side brackets and front rail. Kept all the OEM belt safety features. As set up a couple of posts up, for no rear hump mount.
0 2021/05/18 16:25:49
Removed bosses where bolts go into side of OEM seat
Removed bosses where bolts go into side of OEM seat
0 2021/05/18 16:25:48
0 2021/05/17 15:59:56