Miata Turbo Forum - Boost cars, acquire cats.
0 2016/07/14 11:00:21
0 2016/06/29 16:39:16
Here you can clearly see where the middle divider melted away. Could this have been caused by the switch being faulty?
Here you can clearly see where the middle divider melted away. Could this have been caused by the switch being faulty?
0 2016/06/29 15:06:16
Does this switch look like it needs to be replaced?
Does this switch look like it needs to be replaced?
0 2016/06/29 15:05:52
top view of damaged area
top view of damaged area
0 2016/06/29 15:05:20
This area circled in red is discolored and looks melted
This area circled in red is discolored and looks melted
0 2016/06/29 15:05:02
Here is a close up of what looks like melted plastic
Here is a close up of what looks like melted plastic
0 2016/06/29 15:04:43
Does this look like my switch is bad? You can see damage on the bottom of the connector
Does this look like my switch is bad? You can see damage on the bottom of the connector
0 2016/06/29 15:04:11
0 2016/04/05 15:06:34
I tested the red wire
I tested the red wire
0 2016/03/19 13:43:59
this is the reading from the power wire on the connector to the back of the gauge.
this is the reading from the power wire on the connector to the back of the gauge.
0 2016/03/19 13:43:53
with the key on.
with the key on.
0 2016/03/19 13:43:45
I dont have a cover for my fuse box, my friend said I should be able to see power on the gauge without a fuse in here, is he wrong?
I dont have a cover for my fuse box, my friend said I should be able to see power on the gauge without a fuse in here, is he wrong?
0 2016/03/19 13:43:37
I don't know what to switch this to, or where I'm supposed to put the prongs.
I don't know what to switch this to, or where I'm supposed to put the prongs.
0 2016/03/14 11:46:46
I dont see an LED o nthe controller itself, and there is no LED wired into the loom
I dont see an LED o nthe controller itself, and there is no LED wired into the loom
0 2016/03/14 11:46:39
with everything hooked up and key switched to on, my radio comes on but the gauge doesn't light up and I'm expecting to see an error message at this point.
with everything hooked up and key switched to on, my radio comes on but the gauge doesn't light up and I'm expecting to see an error message at this point.
0 2016/03/14 10:46:44
another person said to use this big blue wire on the left for the wideband power.
another person said to use this big blue wire on the left for the wideband power.
0 2016/03/14 10:46:27
Someone said I could tap into this blue headlight wire for power for my wideband.
Someone said I could tap into this blue headlight wire for power for my wideband.
0 2016/03/14 10:46:19
IAT wired into the 3&4 spots in the MAF sensor, taped up for weather proofing.
IAT wired into the 3&4 spots in the MAF sensor, taped up for weather proofing.
0 2016/03/14 10:46:12
factory bung hole where I've remove the stock o2 sensor, cant put the wideband in until I get I know the gauge works.
factory bung hole where I've remove the stock o2 sensor, cant put the wideband in until I get I know the gauge works.
0 2016/03/14 10:46:03
under the brake booster, the controller without the sensor hooked up, nice view of everything
under the brake booster, the controller without the sensor hooked up, nice view of everything
0 2016/03/14 10:45:55
instructions said if not using the dimming feature of the gauge then to ground that wire to the same spot as other grounds, so you can see I grounded everything here.
instructions said if not using the dimming feature of the gauge then to ground that wire to the same spot as other grounds, so you can see I grounded everything here.
0 2016/03/14 10:45:47
vacuum and wires through same hole. you can see my grounds right below.
vacuum and wires through same hole. you can see my grounds right below.
0 2016/03/14 10:45:39
it fits decent for the time being
it fits decent for the time being
0 2016/03/14 10:45:32
i tapped into the port that the instructions say to.
i tapped into the port that the instructions say to.
0 2016/03/14 10:45:23
unknown gauge wires, and power/ecu wires in through the firewall
unknown gauge wires, and power/ecu wires in through the firewall
0 2016/03/14 10:45:15
it runs around my driver seat and out of the firewall
it runs around my driver seat and out of the firewall
0 2016/03/14 10:45:07
0 2016/03/14 10:44:56
tracing the wideband analog wire
tracing the wideband analog wire
0 2016/03/14 10:44:47
wideband analog wire from the ecu
wideband analog wire from the ecu
0 2016/03/14 10:44:27
ecu spot isnt permamnent, but I used some vacuum line to run it from the back of the passenger seat around the car lol.
ecu spot isnt permamnent, but I used some vacuum line to run it from the back of the passenger seat around the car lol.
0 2016/03/14 10:44:16
Brain build MS3 bought from Dwink, hooked into factory wiring, with vacuum line.
Brain build MS3 bought from Dwink, hooked into factory wiring, with vacuum line.
0 2016/03/14 10:44:09
Male spade connector on the end of the LC-1 power wire.
Male spade connector on the end of the LC-1 power wire.
0 2016/03/14 10:44:02
#2
#2
0 2015/06/20 16:38:11
#2
#2
0 2015/06/20 16:38:00
#1
#1
0 2015/06/20 16:37:49
#1
#1
0 2015/06/20 16:37:38