What's the maximum current draw on OEM fan circuits?
#1
Senior Member
Thread Starter
iTrader: (8)
Join Date: Mar 2006
Location: Floriduh
Posts: 884
Total Cats: 0
What's the maximum current draw on OEM fan circuits?
Searching for 12" fans as the OEM fans won't fit with the super thick radiator I have. I need to know the maximum current the factory fan circuits can handle. 1996 Miata. Thanks.
#4
Senior Member
Thread Starter
iTrader: (8)
Join Date: Mar 2006
Location: Floriduh
Posts: 884
Total Cats: 0
If you've got a fan that draws high amps, say over 15, you can connect a relay to the OEM fan wire to engage the relay, then run the power wire to a 30 amp power source in the fuse box on the passenger fender, or directly to the battery. I just don't want to hassle with that stuff right now. I've got 2 ebay 12" fans mounted to a lexan plate right now. Problem is the CSF radiator is 53mm thick, the fan standoffs are tall, and I have a RB hollow swaybar, so there's no room to properly mount a shroud and fan assembly. I had to slot the lexan to move it and the fan assembly as close to the rad as possible. With the lexan so close to the rad core, I am concerned that airflow through the radiator is going to suck, so I want to direct mount a couple fans to the core using aluminum straps bolted to the radiator's fan standoffs. If I do that I want fans that are going to pull enough air to get the job done. That's why I want to know what the OEM circuits can handle so I know what I can get.
#5
Boost Pope
iTrader: (8)
Join Date: Sep 2005
Location: Chicago. (The less-murder part.)
Posts: 33,046
Total Cats: 6,607
In your '96, each fan has its own relay and its own fuse. The A/C fan shares its fuse with the A/C clutch, but apart from that they're pretty stout circuits.
If you want to trigger both fans to come on when the cooling circuit triggers, just put a jumper wire between the two relay coils. Black / Green at ECU 1A is the main fan, Blue / White at ECU 1B is the A/C fan. This way, you're letting the relays do their job normally, you're just forcing them both on. This has been covered in my A/C FAQ: https://www.miataturbo.net/forum/showthread.php?t=20954
Also, checkit: http://www.fatcatmotorsports.com/fanshroud.htm
#6
Rich, FYI I have 2 of those ebay fans mounted to my rad right now and I havent had any cooling problems. I've spent countless hours in traffic since I installed them and they seem to work just fine.
__________________
Best Car Insurance | Auto Protection Today | FREE Trade-In Quote
__________________
Best Car Insurance | Auto Protection Today | FREE Trade-In Quote
#8
I have been running both of my fans in parallel off of the same circut for a year now and havent had any issues?
__________________
Best Car Insurance | Auto Protection Today | FREE Trade-In Quote
#10
__________________
Best Car Insurance | Auto Protection Today | FREE Trade-In Quote
#12
Also, checkit: http://www.fatcatmotorsports.com/fanshroud.htm
In the video he goes as far as saying that fans are the primary source of air to the rad, and that the next best would be to fully expose the entire rad by hacking up the fascia...
However I'm not totally sure how I feel about the exercise he did since it was only with the shroud in place...Before and after wouldv'e been a little more convincing...
Whats the verdict on this or is the jury still out?
#13
Tour de Franzia
iTrader: (6)
Join Date: Jun 2006
Location: Republic of Dallas
Posts: 29,085
Total Cats: 375
Is everyone in agreement with this video? I've seen the back and forth thats come up, but doesnt seem to be a definitive answer..
In the video he goes as far as saying that fans are the primary source of air to the rad, and that the next best would be to fully expose the entire rad by hacking up the fascia...
However I'm not totally sure how I feel about the exercise he did since it was only with the shroud in place...Before and after wouldv'e been a little more convincing...
Whats the verdict on this or is the jury still out?
In the video he goes as far as saying that fans are the primary source of air to the rad, and that the next best would be to fully expose the entire rad by hacking up the fascia...
However I'm not totally sure how I feel about the exercise he did since it was only with the shroud in place...Before and after wouldv'e been a little more convincing...
Whats the verdict on this or is the jury still out?
Don't forget that a properly molded shroud on the front-side of the rad ideally conformed to the shape of the mouth will be superior to just sticking a head exchanger out front. I looked at a bunch of $$$ race cars and they all do this. Look at the size of the vent on racecars, the molding, and the pressure differentially behind.
#14
Tour de Franzia
iTrader: (6)
Join Date: Jun 2006
Location: Republic of Dallas
Posts: 29,085
Total Cats: 375
I also didn't see anything on that guy's cardomain page about the undertray or shrouding. I assume that yet another person decided that rather than build a shroud to force air through the radiator, they just put fans on it to pull it through.
#15
Oh i NO way was I considering paying for something like that...I have a sheet of ABS that I was thinking would work nicely as a shroud..
Ideally, my thought is to shroud as you said from the opening of the mouth, the sides of the rad, and also the fans behind it...
But again, heard nothing bad about the mouth/sides being shrouded...the dispute seems to be over doing a fan shroud... I'd also think some of the info gathered from people doing hood extractors would apply here no? I could EASILY be misunderstanding this, but it seems related to where one of these works and the other not so much no?
Ideally, my thought is to shroud as you said from the opening of the mouth, the sides of the rad, and also the fans behind it...
But again, heard nothing bad about the mouth/sides being shrouded...the dispute seems to be over doing a fan shroud... I'd also think some of the info gathered from people doing hood extractors would apply here no? I could EASILY be misunderstanding this, but it seems related to where one of these works and the other not so much no?
#16
Tour de Franzia
iTrader: (6)
Join Date: Jun 2006
Location: Republic of Dallas
Posts: 29,085
Total Cats: 375
I'm no expert, but I'm going to fiberglass a shroud for the front side of the rad to the mouth, then work on the undertray, then new fans and a shroud, then cut the hood as a last resort.
I just wanted to point out that this guy built the fan shroud before he looked at the undertray or directing air into the heat exchangers. I hope this plays out in my favor because I'm tired of spending money.
I just wanted to point out that this guy built the fan shroud before he looked at the undertray or directing air into the heat exchangers. I hope this plays out in my favor because I'm tired of spending money.
#17
I hear ya, I feel the same. I'd rather look into shrouding everything so I know the heating isnt due to a lack of air... Also not to keen on cutting my hood (aka *****)...
I have my undertray started, and thats going in soon. I've been waiting for my GS rad to do anythign else (shrouding, fans, etc..).
I'm trying to do things piece by piece so I can judge what kind of difference each solution/suggestion makes...I wouldn't say I have the worst overheating problems, but I think ANY is too much at this point...
Guess this basically falls into trial and error...
I have my undertray started, and thats going in soon. I've been waiting for my GS rad to do anythign else (shrouding, fans, etc..).
I'm trying to do things piece by piece so I can judge what kind of difference each solution/suggestion makes...I wouldn't say I have the worst overheating problems, but I think ANY is too much at this point...
Guess this basically falls into trial and error...
#18
Tour de Franzia
iTrader: (6)
Join Date: Jun 2006
Location: Republic of Dallas
Posts: 29,085
Total Cats: 375
I've always thought that the heat exchangers should do their job without the fans, that's what race cars do. The fans are for street driving. Hopefully a fat lip on the undertray and the front side shrouding will get the job done.
#19
I can't see how a leaf blower with a focused jet of air is going create an accurate representation of the oncoming air at speed. I honestly think the best approach is to install the fans first and then see what happens. If you're getting high temps in traffic and at stop, then the shroud probably will help. But at speed the air is being forced through a much smaller exit area.
#20
Tour de Franzia
iTrader: (6)
Join Date: Jun 2006
Location: Republic of Dallas
Posts: 29,085
Total Cats: 375
I can't see how a leaf blower with a focused jet of air is going create an accurate representation of the oncoming air at speed. I honestly think the best approach is to install the fans first and then see what happens. If you're getting high temps in traffic and at stop, then the shroud probably will help. But at speed the air is being forced through a much smaller exit area.