Stupid nut size for stupid PPF bolt
So I just pulled my motor and tranny and put it back.
The PPF bolts onto the diff with two bolts. The rearmost bolt does not thread into anything so I assume some stupid nut is supposed to hold onto it place where it pokes out above the diff. What is the size of that stupid nut? They didn't have that shizat at home depot. Side queszation. What is the tip/trick to get the shifter to sit in the middle of the shifter hole. My shifter is kinda sitting towards the driver's side which feels kinda wierd. |
The tip for getting the shifter to sit in the middle is to correctly install your engine and transmission. I don't see how it could not be centered. There may be a bit of adjustment in the PPF if you loosen the bolts, adjust the trans whichever way, and then tighten while someone holds it in place. But there can't be whole lot of play in there.
You sure your engine mounts aren't sitting on something? Did you use the engine mount "cover" things? As for the PPF, I thought that "nut" was part of the PPF. As in, welded to it. Or at least press fit. |
Originally Posted by FRT_Fun
(Post 824250)
The tip for getting the shifter to sit in the middle is to correctly install your engine and transmission. I don't see how it could not be centered. There may be a bit of adjustment in the PPF if you loosen the bolts, adjust the trans whichever way, and then tighten while someone holds it in place. But there can't be whole lot of play in there.
As for the PPF, I thought that "nut" was part of the PPF. As in, welded to it. Or at least press fit. |
Just for you, Faeflora, I'm going outside in this 5F weather to check on this and get you a picture. BRB.
|
Also why did you remove the PPF at the diff?
|
Yeah, Faeflora, you are mixed up bro after looking at how my PPF was.
http://virkki.com/jyri/miata/ppf/ Reverse of this. |
Originally Posted by FRT_Fun
(Post 824256)
Also why did you remove the PPF at the diff?
Originally Posted by blaen99
(Post 824257)
Yeah, Faeflora, you are mixed up bro after looking at how my PPF was.
http://virkki.com/jyri/miata/ppf/ Reverse of this. |
Take bolt to your nearest hardware store,
Test nuts, Profit Only solution you've got then, bro. Unless you plan on ordering them online and waiting several days for them at least, you'll have to go to the hardware store anyways. |
Originally Posted by blaen99
(Post 824265)
Take bolt to your nearest hardware store,
Test nuts, Profit Only solution you've got then, bro. Unless you plan on ordering them online and waiting several days for them at least, you'll have to go to the hardware store anyways.
Originally Posted by Faeflora
(Post 824249)
They didn't have that shizat at home depot.
|
Originally Posted by Faeflora
(Post 824268)
...
Fae, there are special nuts on the PPF. They have specialized splined collars to inset into it/fit into the PPF. You won't find them at a hardware store. They are specialized Mazda nuts for the specific PPF application. However, they also take a good deal of force to remove - they are, as another poster mentioned, basically "welded" into the PPF because of how they fit. I cannot imagine how you got them out and misplaced them - if you removed them, you would have had to have worked at it with a hammer at least as they are press-fit with a splined collar. This is what FRT and I have been getting at in this thread. |
Are you sure you are using the correct bolts?
|
1 Attachment(s)
|
yeah I just took my PPF off a week ago. There are two nuts on each bolt that must come out to remove the PPF from the rear diff. They have a shoulder on them that goes into the PPF...a regular ol nut might work but it will be THE SUCK. Don't do it. Find the correct nut.
|
Call me crazy, but aren't the pressed nuts clearly visible in the picture he just posted? I'm not at home to check, but I did this not to long ago. If I remember right one bolt is larger than the other and this was important in putting it together.
|
I think hey are all the same diameter
Per the link, "the bolt closest to the diff simply screws out". Mine slides inand out. No screwing. Ha |
Originally Posted by Faeflora
(Post 824352)
I think hey are all the same diameter
Per the link, "the bolt closest to the diff simply screws out". Mine slides inand out. No screwing. Ha You should have told me last week since I was at a junk yard pulling a diff. Anyways, as far as I know they aren't sold separate of the PPF. |
Why do you break the stupidest sh!t
|
Originally Posted by viperormiata
(Post 824355)
Why do you break the stupidest sh!t
|
OMFG if i lost that ---- well fuc that. I cannot gay out and skip this ----. I broke my old ppf at 250hp so i dunwanna f around on this now. Arrrgggggg
Thing is if there is indeed a press in threaded nut thing, it would have to go into the diff at the top. There is no room as it is tight fit on the bottom. Im gonna use any old fukin bolt and nut that will sorta fit if i cannot get thi shi figured out |
Are they all the same length? Is that front bolt that's already in perhaps a bit longer and supposed to go in the rear hole?
|
All times are GMT -4. The time now is 04:33 AM. |
© 2024 MH Sub I, LLC dba Internet Brands