Super Rich Idle After MS Install
#1
Elite Member
Thread Starter
iTrader: (13)
Join Date: Oct 2006
Location: Atlanta, GA
Posts: 8,091
Total Cats: 7
Super Rich Idle After MS Install
Now that I have MS installed but i have it setup so I can switch between MS and the stock ECU I can't seem to figure out why it idles so rich running on the stock ECU.
My WB is reading 10.0 which is as rich as it will read, if I give it gas it goes up to 12 and right back to 10.
I reset the ECU by pulling the neg battery terminal and letting it sit for 10 minutes then holding the brake for like 15 seconds to discharge any other power in the system. This didn't fix anything.
I checked all vacuum leaks, that's not the problem.
When starting it i have to turn it over once, it'll start and jump up to like 1200 rpm, run a second then die. THen i can try and start it again and give it a bit of gas, then it will run idle again once i let off the pedal.
I'm not expecting people to troubleshoot what i've done, but is there anything that someone could think of causing this?
My WB is reading 10.0 which is as rich as it will read, if I give it gas it goes up to 12 and right back to 10.
I reset the ECU by pulling the neg battery terminal and letting it sit for 10 minutes then holding the brake for like 15 seconds to discharge any other power in the system. This didn't fix anything.
I checked all vacuum leaks, that's not the problem.
When starting it i have to turn it over once, it'll start and jump up to like 1200 rpm, run a second then die. THen i can try and start it again and give it a bit of gas, then it will run idle again once i let off the pedal.
I'm not expecting people to troubleshoot what i've done, but is there anything that someone could think of causing this?
#2
Elite Member
iTrader: (5)
Join Date: Jul 2006
Location: Central California
Posts: 2,546
Total Cats: 4
well if you messed up some wiring obviously. Let me ask a few questions to point you where I would look first.
1. So your WB02 is reading rich and your car is acting accordingly shitty right?
2. Do you have a proper narrowband signal going into the stock ecu (Narrowband sensor or LC1 simulated)?
3. Have you checked your wiring for shorts? In particular you might want to look at the wiring for the o2 sensor, AFM, throttle body, and fuel injector outputs.
Electronics can be a bitch eh? In all honesty, it sounds more like a vaccum leak than anything else so double check that stuff. Make sure your vac line to MS is hooked up and go over everything again.
1. So your WB02 is reading rich and your car is acting accordingly shitty right?
2. Do you have a proper narrowband signal going into the stock ecu (Narrowband sensor or LC1 simulated)?
3. Have you checked your wiring for shorts? In particular you might want to look at the wiring for the o2 sensor, AFM, throttle body, and fuel injector outputs.
Electronics can be a bitch eh? In all honesty, it sounds more like a vaccum leak than anything else so double check that stuff. Make sure your vac line to MS is hooked up and go over everything again.
#6
Are you sharing the stock coolant temp sensor? My guess would be that you didn't remove the bias resistors in the MS which is causing the stock ecu to think the engine is colder than it really is. You will probably also notice your fan doesn't kick on till around 250 degrees.
If you are sharing the sensor remove the bias resistors in the MS, use easy therm with your stock ecu bias resistance (I posted on how to find that a while back), and you'll be good to go from there.
If you are sharing the sensor remove the bias resistors in the MS, use easy therm with your stock ecu bias resistance (I posted on how to find that a while back), and you'll be good to go from there.
#7
Elite Member
Thread Starter
iTrader: (13)
Join Date: Oct 2006
Location: Atlanta, GA
Posts: 8,091
Total Cats: 7
I did remove the bias resistors and attempted to reflash with Easytherm. Something didn't work right with that though.
I just removed the entire MS system from the car. Hooked everything back up and the car still runs rich. I'm disconnecting the wideband from the ECU 12v and grounds cause I think that might be giving me a messed up reading but i'm not sure about that.
Also, when starting it I now have to turn it over once. Then try again and give it a little gas to get it to idle. The first time i turn it over it will run for a second and die.
What the hell did I do? I guess i need to check all my wiring again because maybe one of my crimps is messed up. I'll check that tonight.
I just removed the entire MS system from the car. Hooked everything back up and the car still runs rich. I'm disconnecting the wideband from the ECU 12v and grounds cause I think that might be giving me a messed up reading but i'm not sure about that.
Also, when starting it I now have to turn it over once. Then try again and give it a little gas to get it to idle. The first time i turn it over it will run for a second and die.
What the hell did I do? I guess i need to check all my wiring again because maybe one of my crimps is messed up. I'll check that tonight.
#11
Elite Member
Thread Starter
iTrader: (13)
Join Date: Oct 2006
Location: Atlanta, GA
Posts: 8,091
Total Cats: 7
Fixed the problem tonight.
Spend an hour repairing previously destroyed damaged wires that had been electrical taped up. I removed all that can be described as being a "the worst wiring ever" and then resoldered everything back together.
That's what I get for buying someone elses project.
I pretty much brought the harness back to stock form now and will be building a pnp harness from the boomslang connector i ordered today.
I've made up my mind to never modify a stock harness unless there are no other options.
In short. Spend the $30 to get the female boomslang connector. $20 for the part $10 to ship.
Spend an hour repairing previously destroyed damaged wires that had been electrical taped up. I removed all that can be described as being a "the worst wiring ever" and then resoldered everything back together.
That's what I get for buying someone elses project.
I pretty much brought the harness back to stock form now and will be building a pnp harness from the boomslang connector i ordered today.
I've made up my mind to never modify a stock harness unless there are no other options.
In short. Spend the $30 to get the female boomslang connector. $20 for the part $10 to ship.
Thread
Thread Starter
Forum
Replies
Last Post
StratoBlue1109
Miata parts for sale/trade
21
09-30-2018 01:09 PM
stoves
Suspension, Brakes, Drivetrain
5
04-21-2016 03:00 PM