Utopian Drivetrain
So I've been wondering for a while what the best engine and/or trans. setup would be based on hp and tq potential (and where they are in the power band), responsiveness, reliability, and such. Basically, if you weren't restricted by money, time, or space what engine would you be rockin'? One restriction: it has to be a production engine...otherwise we'd all say an old school F1 engine running 50psi. And one other thing, I guess I should specify that it would be for road racing and not drag, although if you want to list some good drag engines go ahead.
|
Turbo KL-DE with T5 trans.
|
Judd V8 with straigh-cut sequential dogbox. If that's not production enough, built LSx with afore mentioned tranny.
|
2JZ-GTE. Getrag 6 speed.
|
Maytag horizontally opposed twin from the random picture thread and a sequential gearbox from a KZ125.
|
BMW S85 V10 with the new 7 speed DSG transmission
|
|
20B 3-rotor with 6spd trans from Japanloand FD RX-7 to a 3.63 r&p w/OSG LSD.
|
8.4 viper v10 w/ t56
|
Bored and Stroked 2.5 MZR with Cosworth cyl head, giganticam, and IRTBs.
What ever transmission and rearend that would hold up to an all out N/A MZR. Maybe nitrous. :nxsmile: |
In the miata right? All aluminum LS v8 motor with some badass heads and valvetrain, sequential gearbox, tru-trac or whatever diff is similar to a Torsen but can handle the power. Torque baby.
|
Normally aspirated, high compression, high rev, bigger cube, wide powerband, light small lump tucked lower and further back. Could be 4 or 6 holes with this car without making it too unbalanced.
|
4 wheel drive. Two LS motors. One front mount. One rear mount. Single 100mm turbo for both motors. Or something like that. |
Originally Posted by TurboTim
(Post 730332)
Turbo KL-DE with T5 trans.
Judd V8 with straigh-cut sequential dogbox Or: One of those busa v8 jobs, punched out to 3.2L. Do a bunch of porting and bullshit and make the redline sky-high (like 13-14k). Staged shower injectors above the velocity stacks. Keep the bike trans for sequential action, with a button on the dash you press for reverse. ^If that isn't production enough, turbo busa motor, punched to 1.6L. same shit. Run a shaft off of where the chain drive would go. Rear end something with an OS giken something. |
Originally Posted by Doppelgänger
(Post 730459)
20B 3-rotor with 6spd trans from Japanloand FD RX-7 to a 3.63 r&p w/OSG LSD.
But custom fab housings and whatever else I could out of titanium. Also a boost for good measure. |
Originally Posted by Doppelgänger
(Post 730459)
6spd trans from Japanloand FD RX-7
imaginary tranny is imaginary? Or did you mean like an aftermarket dog-box? |
Pratt and Whitney F119-PW-100 turbofan.
|
Originally Posted by shooterschmidty
(Post 730587)
Pratt and Whitney F119-PW-100 turbofan.
|
Ford Racing 427 Boss (500/500 in NA config), T-56 w/GM F-body gearing (4th = 1:1, 5th = 0.75, 6th = 0.50), '99 Cobra 8.8 IRS Torsen w/ final drive to match final HP/TQ numbers....
...then write Corky a blank check to "improve" things! - L |
Originally Posted by ThePass
(Post 730522)
In the miata right? All aluminum LS v8 motor with some badass heads and valvetrain, sequential gearbox, tru-trac or whatever diff is similar to a Torsen but can handle the power. Torque baby.
|
All times are GMT -4. The time now is 11:54 PM. |
© 2024 MH Sub I, LLC dba Internet Brands