Originally Posted by concealer404
(Post 954139)
Well, and neither of those really seal that well when just jammed over some -10AN male fittings previously welded into my valve covers.
It's BECAUSE RACE CAR at this point whether i like it or not. |
1 Attachment(s)
Originally Posted by Rennkafer
(Post 954320)
I built race cars professionally... we used reinforced tygon hose on vent lines. Three reasons, it's lighter (light = good), it's cheaper (cheap = good), and you can see when stuff is venting or not with it. Sealed just fine with a good quality hose clamp.
Yes, the transmission is hideous. Oh well. :giggle: https://www.miataturbo.net/attachmen...ine=1354204505 |
these may be of use to you then: Fragola -10an 90 Degree Push-Lite Race Hose End
(ignore seller, I was just searching for -10an nipple fitting) |
Nice build, but I've got to ask.. Why an fittings as breathers to the catch can and brass fittings with regular fuel line on your fuel rails?
|
Check out AN Fittings Direct, they are the same company that does siliconeintakes.com. I have been reasonably happy with the fittings from them in the past. Now I only use Aeroquip though, but that is because I can buy them locally. Honestly if you already paid to have the VC welded, stop being extremely cheap on the fittings. I have used cheap fittings in the past and they have always been a bigger pita then the money I saved has been worth.
|
Originally Posted by Preluding
(Post 954752)
these may be of use to you then: Fragola -10an 90 Degree Push-Lite Race Hose End
(ignore seller, I was just searching for -10an nipple fitting)
Originally Posted by Boost_addict
(Post 954753)
Nice build, but I've got to ask.. Why an fittings as breathers to the catch can and brass fittings with regular fuel line on your fuel rails?
Originally Posted by shuiend
(Post 954761)
Check out AN Fittings Direct, they are the same company that does siliconeintakes.com. I have been reasonably happy with the fittings from them in the past. Now I only use Aeroquip though, but that is because I can buy them locally. Honestly if you already paid to have the VC welded, stop being extremely cheap on the fittings. I have used cheap fittings in the past and they have always been a bigger pita then the money I saved has been worth.
|
Maybe it's time to just buy the Ebay fittings and be the crash test dummy. If something blows up I'll help you fix it.
|
Originally Posted by thenuge26
(Post 954764)
Maybe it's time to just buy the Ebay fittings and be the crash test dummy. If something blows up I'll help you fix it.
|
1 Attachment(s)
Originally Posted by Boost_addict
(Post 954753)
Nice build, but I've got to ask.. Why an fittings as breathers to the catch can and brass fittings with regular fuel line on your fuel rails?
Better? :) https://www.miataturbo.net/attachmen...ine=1354485562 |
1 Attachment(s)
Well the fail has arrived. I'll be sure to document my absolutely terrible experiences with them that will eventually push me to consider suicide.
https://www.miataturbo.net/attachmen...ine=1354633357 |
Did I mention I used 1 ebay fitting (I had it kicking around) for my oil drain feed? Another zero pressure line...
it slowly seeps oil out...not a huge leak, just a drip every now and then, just enough to piss me off. |
Originally Posted by Preluding
(Post 955882)
Did I mention I used 1 ebay fitting (I had it kicking around) for my oil drain feed? Another zero pressure line...
it slowly seeps oil out...not a huge leak, just a drip every now and then, just enough to piss me off. |
1 Attachment(s)
BRB suiciding.
Ok, actually... these were pretty painless. No, they didn't FEEL as good as the XRP/Earl's/Aeroquip stuff i used everywhere else, but they assembled easily, fit fine, and the threads were fine. Would i use them for liquids? Nah. Are they going to be just fine for this? Yep. https://www.miataturbo.net/attachmen...ine=1354888850 |
Who made your catch can?
|
Originally Posted by shuiend
(Post 956767)
Who made your catch can?
|
Originally Posted by concealer404
(Post 956768)
Dude named Wade in Louisville. He welded the bungs into the valve covers as well.
I am planning on building me one similar to that in the spring. So I might be asking you for some more pictures of it in the springtime. |
2 Attachment(s)
Originally Posted by shuiend
(Post 956770)
How much did he charge to make the catch can?
I am planning on building me one similar to that in the spring. So I might be asking you for some more pictures of it in the springtime. He might have another available if you're interested. He typically makes these for Hondas, they fit nicely where the batteries used to go. https://www.miataturbo.net/attachmen...ine=1354897254 https://www.miataturbo.net/attachmen...ine=1354897254 |
All times are GMT -4. The time now is 05:45 AM. |
© 2024 MH Sub I, LLC dba Internet Brands