General Miata Chat A place to talk about anything Miata

Front suspension issue?

Thread Tools
 
Search this Thread
 
Old 10-06-2006, 09:25 PM
  #1  
Senior Member
Thread Starter
 
firedog25's Avatar
 
Join Date: May 2006
Posts: 917
Total Cats: -8
Default Front suspension issue?

I suspect a done wheel bearing, but it only does this under load. For example, turning. It's a mild grinding noise, I suppose it could be brake related though but I haven't driven hard since I replaced the brakes a year ago, but how would I figure out if the wheel bearing is bad?
firedog25 is offline  
Old 10-06-2006, 10:32 PM
  #2  
Senior Member
iTrader: (1)
 
kung fu jesus's Avatar
 
Join Date: Dec 2005
Location: irvine, ca
Posts: 729
Total Cats: 0
Default

raise up the car, grab the tire at 12 and 6 o'clock and try to wiggle it fore and aft. if it does, your bearing is toast. ~$115 for a timken hub assembly at autozone. takes 20 minutes to install, you need a 32 or 34mm (?) socket to remove the nut.
kung fu jesus is offline  
Old 10-06-2006, 10:45 PM
  #3  
Senior Member
Thread Starter
 
firedog25's Avatar
 
Join Date: May 2006
Posts: 917
Total Cats: -8
Default

Cool! An opportunity to buy another tool?
firedog25 is offline  
Old 10-06-2006, 11:38 PM
  #4  
Newb
 
BEGITechRep's Avatar
 
Join Date: Dec 2005
Location: San Antonio
Posts: 29
Total Cats: 0
Default

If its the *front hub*, you only need 12mm, 14mm, and 17mm sockets and wrenches. The lower arm ball joint is the hardest part of the job. The hubs I've seen come as a one-piece assembly.

The rear hub uses the big monster...29mm IIRC but I'd have to go look at my 3/4" drive tools and those are almost 1000 miles away for the moment...

Check the brakes and brake shield first. I once had a brake shield that would be pressed against the disc only at full lock. Drove me nuts trying to find the noise...

Barry
BEGITechRep is offline  
Old 10-07-2006, 10:08 PM
  #5  
Senior Member
Thread Starter
 
firedog25's Avatar
 
Join Date: May 2006
Posts: 917
Total Cats: -8
Default

Actually, I replaced the lower ball joint a year ago, those were pretty easy with the help of Mr. Deadblow. I think I also have the brake shield problem because I get a weird grind at full lock, perhaps that is part of the problem?

Also, I need to replace my exhaust hangers, they're mushy like pudding.
firedog25 is offline  
Old 10-08-2006, 12:06 AM
  #6  
Senior Member
iTrader: (1)
 
miataspeed1point6's Avatar
 
Join Date: Feb 2006
Location: Detroit
Posts: 1,234
Total Cats: 0
Default

Sounds like a wheel bearing. At work when I go on test drives to check for wheel bearings I turn the wheel back and forth. If only one bearing is bad the grinding will happen one way, but not the other. Do exactly what KFJ said. While your in there check out the rest of your ball joints and tie rods.
miataspeed1point6 is offline  
Old 10-08-2006, 05:02 PM
  #7  
Senior Member
Thread Starter
 
firedog25's Avatar
 
Join Date: May 2006
Posts: 917
Total Cats: -8
Default

NM, I figured it out. It's my stupid exhaust as it swings one way or another and rattles against all hell and creation. My hangers are all mushy and it will settle against the tranny and vibrate making the weird noise. It resonates across the driver's side and makes ugliness!
firedog25 is offline  
Related Topics
Thread
Thread Starter
Forum
Replies
Last Post
Full_Tilt_Boogie
Build Threads
84
04-12-2021 04:21 PM
bigmackloud
Miata parts for sale/trade
19
01-08-2021 11:24 AM
interestedofold
Suspension, Brakes, Drivetrain
5
09-29-2015 01:42 PM
zephyrusaurai
Meet and Greet
2
09-28-2015 10:59 PM



Quick Reply: Front suspension issue?



All times are GMT -4. The time now is 10:11 PM.