baby needs a BATH.
maybe an engine bay detail. scott embarassed me in my leakdown thread by showing my dirty underdrawers. |
[QUOTE=hustler;858128]Turbo car:[LIST][*]Send turbo to Europe[*]Make real AN lines/fittings for the turbo lines
I was going to do this last night minus the Starlight but the local speed shop did not have whatever size AN a 5/16 hose is... which is AN 5, which is not common since most places only stock even. guess all the shops had a meeting to boycott odd sizes so now goes on the fuel line or turbo water lines until I decide how to re pipe the water lines. think I will pull from the front plug in the reroute kit and then do a tee. |
Anyone get top down road head? Trying to cross that off the list this year.
|
I think that is a different list
|
ended up getting an upright for $44 shipped. That thing was not going to come out. We ended up mushrooming the axle with a 4 lb sledgehammer.
|
Originally Posted by psreynol
(Post 858068)
ha I did not really look at it very carefully, its just a bottle jack attached to a frame, think I would not do much damage
|
well I leaned what can happen with half drunken welding other other night when I decided to start modifying my seat bracket late at night. lets just say I have a new rule. no welding after I've stopped work for the night. I also I think its time to make a welding table and get gloves and a real mask
|
Rape my car and trauamatize it
To inspire it to Rape abd traumatize other cars. It's the cirrrrclee of liiiiiiiffeeeee!!! |
Originally Posted by Faeflora
(Post 859469)
Rape my car and trauamatize it
To inspire it to Rape abd traumatize other cars. It's the cirrrrclee of liiiiiiiffeeeee!!! |
Install LC-1 and MS2, tune, drive to Houston tomorrow. I can't bare to not install this ----.
|
Replace broken 5spd with Quaife
Paint cage Put blowers in brake cooling Meters in dash Permanent 12V for acc (video cam etc) goes on and on |
drop car off with Moti. :)
|
Originally Posted by spaztikcamel
(Post 854230)
list of stuff i probably will do
fm clutch front sway bar tse bbk 6ul's and good tyres t28 rather than my current t25 new steering wheel and race seats oil cooler radiator ducting and extraction vent spoiler and splitter list of stuff id like to do but probably wont ls3 conversion run cordycords chassis |
Figure out oil temp sender issue.
Decide on seats that a) have sliders b) take harnesses c) work with door bars and d) lower me a bit more than my double-foamectomy currently does. Change oil after Monday's track event. Finish the tire trailer and test drive it next week. |
1. Fix A/C. Evaporator has holes and South Florida gets hot this time of year.
2. Replace busted alignment bolts. Can't get proper alignment without them. 3. Get alignment. I want to use Flyin' Miata's recommended settings. 4. Get more seat time at the local auto-x :) |
1. Drive
2. Add fuel 3. Drive |
- fab new oil pick up tube
- test fit engine position for trans, drive shaft, front sway bar, CAS fit, and oil pan dimensions - fab new oil pain - .63 AR Turbine housing? new IWG housing or EWG? - fab new downpipe and adjust exhaust to fit - fab new exhaust manifold support arm - fab new intake manifold support arm - set up IAC and injectors for new intake manifold - install EMU (link or other?) - Fab adapter for 04/05 AC compressor - Fab AC lines to fit new compressor or 04/05 lines/condenser/drier or custom - Fab radiator/oil cooler carrier - Set up new dual fans for oil/AC (dual trigger) and rad cooling - Oil cooler lines - Remove one shim from oil pump - paint engine bay ... |
Originally Posted by phillyb
(Post 857663)
rebuild
more chrome more flowers |
|
1. Get the fricking bonded title.
2.a. Sell, or 2.b. Part out. |
All times are GMT -4. The time now is 08:24 PM. |
© 2024 MH Sub I, LLC dba Internet Brands