Turbo Manifolds and Misc. Fab

 
Old 02-01-2007, 05:34 PM
  #1  
Supporting Vendor
Thread Starter
iTrader: (7)
 
Join Date: Mar 2005
Location: Broken Arrow,Ok
Posts: 1,142
Total Cats: 34
Default Turbo Manifolds and Misc. Fab

For some time now I have been doing fabrication work, mostly IC piping, downpipe, wastegate dumps, etc. Most of this was from local guys, but I have a few interested in manifolds and such on here, so I might as well make a formal post of it. I have the ability to make whatever is needed, but I think my main focus will be turbo manifolds, possibly downpipes. Let me know if there is any interest, as most of these will made to order.
-Michael-
__________________


95 Miata Backburner Project
99 Jeep Cherokee Offroad Beater
01 Miata AutoX Car
02 Bugeye Wagon Project Car
07 335i Fun Daily

Check Out Our Parts Threads and Online Store!
Coolant Reroute and EGR Block-Off Parts Thread
LSx D585 Coil Bracket Kit Pre-Order Thread

Hawley Performance Online Store
TheBandit is offline  
Leave a poscat 0 Leave a negcat
Old 02-01-2007, 07:08 PM
  #3  
Supporting Vendor
Thread Starter
iTrader: (7)
 
Join Date: Mar 2005
Location: Broken Arrow,Ok
Posts: 1,142
Total Cats: 34
Default

I made the one on my car, but lets just say it wasn't easy. So you are looking for a pipe that comes out from the TB and goes down a bit, to connect your other IC piping to? What material?
-Michael-
__________________


95 Miata Backburner Project
99 Jeep Cherokee Offroad Beater
01 Miata AutoX Car
02 Bugeye Wagon Project Car
07 335i Fun Daily

Check Out Our Parts Threads and Online Store!
Coolant Reroute and EGR Block-Off Parts Thread
LSx D585 Coil Bracket Kit Pre-Order Thread

Hawley Performance Online Store
TheBandit is offline  
Leave a poscat 0 Leave a negcat
Old 02-01-2007, 08:04 PM
  #5  
y8s
2 Props,3 Dildos,& 1 Cat
iTrader: (8)
 
y8s's Avatar
 
Join Date: Jun 2005
Location: Fake Virginia
Posts: 19,170
Total Cats: 507
Default

I build my own stuff but if I were goin to do more than a couple for various DIY setups.... I'd make a generic any-turbo setup. You figure you can leave some length in the dp where the exducer would be or maybe make some modular 90's to fit various flanges. and then build the header with no flange and then fit up whatever one you want... maybe make a flangeless header that you can just stitch on a flange when you have a buyer.

if that's feasible. they'd have to ship you the turbo to finish it all up.
y8s is offline  
Leave a poscat 0 Leave a negcat
Old 02-02-2007, 05:48 PM
  #6  
Elite Member
iTrader: (3)
 
Join Date: May 2006
Location: Houston, TX
Posts: 2,895
Total Cats: 0
Default

what kind of price could I expect on a durable t3 manifold?
Arkmage is offline  
Leave a poscat 0 Leave a negcat
Old 02-02-2007, 06:12 PM
  #7  
Supporting Vendor
Thread Starter
iTrader: (7)
 
Join Date: Mar 2005
Location: Broken Arrow,Ok
Posts: 1,142
Total Cats: 34
Default

I think a T3 with Stainless runners and an external wastegate runs in the $375 range.
-Michael-
__________________


95 Miata Backburner Project
99 Jeep Cherokee Offroad Beater
01 Miata AutoX Car
02 Bugeye Wagon Project Car
07 335i Fun Daily

Check Out Our Parts Threads and Online Store!
Coolant Reroute and EGR Block-Off Parts Thread
LSx D585 Coil Bracket Kit Pre-Order Thread

Hawley Performance Online Store
TheBandit is offline  
Leave a poscat 0 Leave a negcat
Old 02-02-2007, 09:06 PM
  #8  
Elite Member
iTrader: (13)
 
cjernigan's Avatar
 
Join Date: Oct 2006
Location: Atlanta, GA
Posts: 8,140
Total Cats: 6
Default

Tubular shorty style or log style?
cjernigan is offline  
Leave a poscat 0 Leave a negcat
Old 02-03-2007, 02:40 AM
  #9  
Supporting Vendor
Thread Starter
iTrader: (7)
 
Join Date: Mar 2005
Location: Broken Arrow,Ok
Posts: 1,142
Total Cats: 34
Default

That would be for a Log style. I have the ability to make both.
-Michael-
__________________


95 Miata Backburner Project
99 Jeep Cherokee Offroad Beater
01 Miata AutoX Car
02 Bugeye Wagon Project Car
07 335i Fun Daily

Check Out Our Parts Threads and Online Store!
Coolant Reroute and EGR Block-Off Parts Thread
LSx D585 Coil Bracket Kit Pre-Order Thread

Hawley Performance Online Store
TheBandit is offline  
Leave a poscat 0 Leave a negcat
Old 03-06-2007, 01:00 AM
  #10  
Junior Member
 
Join Date: Oct 2005
Posts: 84
Total Cats: 0
Default

sorry to bring back old threads but are custom Downpipes available as well? and how much would a manifold for a T28 cost with and with out a D/p if available. and if you can please include shipping.
thanks
Jeepster118 is offline  
Leave a poscat 0 Leave a negcat
Old 03-06-2007, 01:07 AM
  #11  
Senior Member
iTrader: (1)
 
Join Date: Dec 2005
Location: irvine, ca
Posts: 729
Total Cats: 0
Default

intercooler system for an m45 s/c?
kung fu jesus is offline  
Leave a poscat 0 Leave a negcat
Old 03-06-2007, 01:35 AM
  #12  
Senior Member
iTrader: (10)
 
Join Date: Feb 2007
Location: South Eastern Wisconsin
Posts: 1,274
Total Cats: 0
Default

Think you could clone your TB inlet? I still haven't made one for myself.. It would save me alot of time.
ApexOnYou is offline  
Leave a poscat 0 Leave a negcat
Old 03-06-2007, 01:46 AM
  #13  
Senior Member
 
boostinsteve's Avatar
 
Join Date: Oct 2006
Location: Honolulu, HI
Posts: 563
Total Cats: 0
Default

Greddy replacement mani? I have a friend that needs to get a new mani, his is cracked real bad.
boostinsteve is offline  
Leave a poscat 0 Leave a negcat
Old 03-06-2007, 01:50 PM
  #14  
Junior Member
 
Join Date: Dec 2005
Posts: 258
Total Cats: 0
Default

I can use a greddy replacement as well, and i'm looking for something that would be an upgrade to the regular one, but hopefully not as pricy as the etd. let me know, cause if i'm ordering the oil line i might as well do both at the same time.
BrillntBlk92 is offline  
Leave a poscat 0 Leave a negcat
Old 03-06-2007, 04:08 PM
  #15  
Supporting Vendor
Thread Starter
iTrader: (7)
 
Join Date: Mar 2005
Location: Broken Arrow,Ok
Posts: 1,142
Total Cats: 34
Default

Sorry guys, I hadn't noticed any threads in here for awhile. I can make just about whatever you want, I just need something to base it off of. And it will take a bit of time to design, make, etc. I dont have anything in stock really, except most of the materials. Let me know what you want and if you have any drawings or models..that kinda show what you are looking for.
-Michael-
__________________


95 Miata Backburner Project
99 Jeep Cherokee Offroad Beater
01 Miata AutoX Car
02 Bugeye Wagon Project Car
07 335i Fun Daily

Check Out Our Parts Threads and Online Store!
Coolant Reroute and EGR Block-Off Parts Thread
LSx D585 Coil Bracket Kit Pre-Order Thread

Hawley Performance Online Store
TheBandit is offline  
Leave a poscat 0 Leave a negcat
Old 03-20-2007, 09:40 AM
  #16  
Tour de Franzia
iTrader: (6)
 
hustler's Avatar
 
Join Date: Jun 2006
Location: Republic of Dallas
Posts: 29,098
Total Cats: 368
Default

could you do a t3 manifold and downpipe for a 1.8? I'm interested...if it can be beefy enough so I don't have to worry about it cracking.

I'd also consider a dp for an hks manifold.
hustler is offline  
Leave a poscat 0 Leave a negcat
Old 03-20-2007, 11:22 PM
  #17  
Junior Member
iTrader: (5)
 
Join Date: Jan 2006
Posts: 345
Total Cats: 0
Default

I'd be really interested in a downpipe that could mate a 1.8l HKS manifold/Greddy Td04h turbo to the stock 94-97 1.8l cat.
tronik is offline  
Leave a poscat 0 Leave a negcat
Old 06-27-2007, 10:34 PM
  #18  
Junior Member
 
Join Date: May 2007
Posts: 119
Total Cats: 0
Default

i was wondering if you can make a turbo mani, with the down pipe for t25 on an 03 miata
mxdrift is offline  
Leave a poscat 0 Leave a negcat
Old 07-04-2007, 04:26 PM
  #19  
Elite Member
iTrader: (12)
 
Join Date: Jan 2007
Location: Hermosa Beach, CA
Posts: 2,573
Total Cats: 11
Default

all I need is a downpipe for the 1.6L, with a 2.5 inch v band on the turbo side..
cardriverx is offline  
Leave a poscat 0 Leave a negcat
Old 07-04-2007, 04:40 PM
  #20  
Senior Member
iTrader: (3)
 
Join Date: Apr 2007
Location: Odenton, MD
Posts: 713
Total Cats: 0
Default

he isn't making them ATM
Dow.tom is offline  
Leave a poscat 0 Leave a negcat

Thread Tools
Search this Thread
Quick Reply: Turbo Manifolds and Misc. Fab


Archive - Advertising - Cookie Policy - Privacy Statement - Terms of Service

© 2019 MH Sub I, LLC dba Internet Brands

We are a participant in the Amazon Services LLC Associates Program, an affiliate advertising program designed to provide a means for us to earn fees by linking to Amazon.com and affiliated sites.