99 motor to 92 miata w/mspnp9093 possible or not
what do i need to convert 92 miata to 99 motor?i was thinking use 1.6 cas and fuel rail,throttle body to 99 motor you think it will work?or is possible pnpms9093 convert to mspnp9495 so i can use 1.8 throtle body,fuel rail and cas.or just sell my mspnp9093 and get mspnp9495?i just wanna use my free 33,000 miles,99 motor.
|
Your 1.6 fuel rail won't work with the 99 1.8. The CAS will work though. The mspnp 9495 won't do anything the 9093 won't do so that isn't a good route to take.
|
I think he already has the 9093MSPNP
|
That's why i told him swapping to a 94-95PNP wouldn't make any difference.
Also if you plan to use the stock harness and connectors i believe the 1.6 ECU connectors differ from the 94-95 1.8 connectors but I'm not positive so that would open a whole new can of worms for you. Atleast with the 90-93pnp and your stock harness you would be able to use the existing wiring again. |
Thats why im a moron and shouldnt be allowed to post with out permission of others
|
everything you needed to know, in one thread, that shows up if you search
https://www.miataturbo.net/showthrea...highlight=vics |
Originally Posted by Ben
(Post 153787)
everything you needed to know, in one thread, that shows up if you search
https://www.miataturbo.net/showthrea...highlight=vics |
you'll have to use a different start setting, but I have that data on my work computer thanks to "foundsoul." No additional parts are needed, just a different tune.
|
Originally Posted by hustler
(Post 153811)
"foundsoul."
It's actually good to hear that I can swap my CAS over to a '99 head and keep on truckin' with the MS. When I bleed money, I'm going to swap a '99 head onto my shortblock. |
Originally Posted by hustler
(Post 153811)
you'll have to use a different start setting, but I have that data on my work computer thanks to "foundsoul." No additional parts are needed, just a different tune.
|
Originally Posted by hustler
(Post 153811)
you'll have to use a different start setting, but I have that data on my work computer thanks to "foundsoul." No additional parts are needed, just a different tune.
|
TWM > Fuji. Fuji's kit uses an adapter for the 99 head. Not so free air for a free flowing head. Boig or TWM ftw.
|
Uh a 1.6 irtb wont work on a 1.8 car the shit i different dude. ANd the 1.8 TB is also different as well. Stick all 1.8 hard stuff and run it off the 1.6 electronics works fine. didn't you read the thread? He got his shit custom machined to work with the 99 intake. And he probably hasn't even been near the miata this month have you hustler.
|
i just did the swap on a 92 car/harness, 96 block, 99 head/mani...you have to use the 1.6 TB, and you will have to cut into the CAS wiring harness and make it longer since it will not reach, you just have to extend the wires by about 4-6" is all you need, the rest was pretty simple...and IRTB, why?
go boost |
Originally Posted by whaaamx5
(Post 155518)
i just did the swap on a 92 car/harness, 96 block, 99 head/mani...you have to use the 1.6 TB, and you will have to cut into the CAS wiring harness and make it longer since it will not reach, you just have to extend the wires by about 4-6" is all you need, the rest was pretty simple...and IRTB, why?
go boost how can i built a good 1.6 what do i need to get and what brand should i trust i have my 1.6 head build with fererra valve reg,supertech valve spring and retainers and 5 angle valve job, and after this i blown the motor coz of my stupidity trusting my buddy about tighning oil filter which he didt i drove the car for 3 miles no oil and now my lower block is knocking,should i build my 1.6 or upgrade to 99 motor. |
Originally Posted by whaaamx5
(Post 155518)
i just did the swap on a 92 car/harness, 96 block, 99 head/mani...you have to use the 1.6 TB, and you will have to cut into the CAS wiring harness and make it longer since it will not reach, you just have to extend the wires by about 4-6" is all you need, the rest was pretty simple...and IRTB, why?
go boost |
Originally Posted by castillejos2000
(Post 157163)
i used to have a boost 1.6 but i wanna try all motor for autox,so i can run sts not sm2 class,what about your aic and your vic you just let open all the time? 1.6 tb ?
how can i built a good 1.6 what do i need to get and what brand should i trust i have my 1.6 head build with fererra valve reg,supertech valve spring and retainers and 5 angle valve job, and after this i blown the motor coz of my stupidity trusting my buddy about tighning oil filter which he didt i drove the car for 3 miles no oil and now my lower block is knocking,should i build my 1.6 or upgrade to 99 motor. Use the 1.6 alternator. Wire the vics to a shift light trigger. The IAC settings for the 99 motor: http://i7.tinypic.com/6be1dl3.jpghttp://i10.tinypic.com/54mehvo.jpg I've been driving the car, but not working on it yet. Everything is still in boxes. Read this, but please don't fill it up with garbage questions. https://www.miataturbo.net/megasquirt-18/mspnp-99-motor-questions-10245/ |
All times are GMT -4. The time now is 09:26 PM. |
© 2024 MH Sub I, LLC dba Internet Brands