|
1 Attachment(s)
Originally Posted by vehicular
(Post 1026015)
The sound.... I skeeted....
My buddy bear: https://www.miataturbo.net/attachmen...ine=1372460365 |
1 Attachment(s)
Originally Posted by triple88a
(Post 1026496)
I'd laugh at a drunk person through the window... an animal though i dont find so funny.
https://www.miataturbo.net/attachmen...ine=1372459940 Attachment 239618 |
1 Attachment(s)
Originally Posted by Fireindc
(Post 1026497)
Well fuck me, that car is amazing. I really don't understand it though, are the electric motors just there to make up for the turbo lag?
https://www.miataturbo.net/attachmen...ine=1372478015 |
2 Attachment(s)
I can practically hear Jamie Hyneman's voice saying "Well there's your problem."
https://www.miataturbo.net/attachmen...1&d=1372481253 Over ten degrees off. No wonder the engine feels like shit, idles at 60 kPa, and is getting 17 MPG. I also re-tested the compression with a decent quality gauge this time. The numbers were nice and even- between 140 and 155 all around, right near the bottom end of the spec. |
1 Attachment(s)
|
1 Attachment(s)
|
1 Attachment(s)
trying to figure out what in the heck is going on in that picture
https://www.miataturbo.net/attachmen...ine=1372482310 |
1 Attachment(s)
|
1 Attachment(s)
Originally Posted by FRT_Fun
(Post 1026566)
Very precise TDC?
https://www.miataturbo.net/attachmen...ine=1372482561 |
Originally Posted by triple88a
(Post 1026567)
Correct, hes using the height gauge to find the TDC.
https://www.miataturbo.net/attachmen...ine=1372482561 http://3ir.net/wp-content/uploads/20...ie-Hyneman.jpg |
Originally Posted by FRT_Fun
(Post 1026569)
I feel like that may be overkill.
https://i.chzbgr.com/maxW500/2593384960/h73AC9F87/ |
1 Attachment(s)
|
2 Attachment(s)
Originally Posted by FRT_Fun
(Post 1026569)
I feel like that may be overkill.
https://www.miataturbo.net/attachmen...1&d=1372483096 |
1 Attachment(s)
Joe isnt there a pin in there thats suppose to prevent that?
https://www.miataturbo.net/attachmen...ine=1372483438 |
1 Attachment(s)
Originally Posted by FRT_Fun
(Post 1026571)
I usually just eyeball it.
|
1 Attachment(s)
Originally Posted by triple88a
(Post 1026575)
Joe isnt there a pin in there thats suppose to prevent that?
The pulley is not one solid piece of metal. It's two pieces, an inner and an outer, bonded together with a rubber ring. As the rubber ages and hardens, it becomes possible for the two halves of the pulley to slip out of alignment. The inner part is still properly aligned with the crank (a woodruff key and pin ensure this), but the outer part is not aligned with the inner part. https://www.miataturbo.net/attachmen...ine=1372484138 This also means that all of the careful work I did optimizing the ignition map is completely for shit. |
If i design a MT 3d model will people buy it from shapeways? ...possibly a 2-3" keychain model.
|
Originally Posted by triple88a
(Post 1026583)
If i design a MT 3d model will people buy it from shapeways? ...possibly a 2-3" keychain model.
|
1 Attachment(s)
Let's not get into 3d printing of guns... because you know... guns are bad.
/sarcasm Besides, there is the gun thread for that. I bet this guitar sounds like complete shit. https://www.miataturbo.net/attachmen...ine=1372530564 |
2 Attachment(s)
The crank is aligned so that the pulley notch is at the "T" mark on the cover.
The black mark on the pulley indicates where TDC actually is. https://www.miataturbo.net/attachmen...1&d=1372530077 Twenty-three degrees. That's how far that little fucker was off. So, yeah. Miatafolk ought to check their pulleys. Cheap dial indicators and cheap magnetic bases are not expensive. |
All times are GMT -4. The time now is 08:09 PM. |
|
© 2024 MH Sub I, LLC dba Internet Brands