2 Attachment(s)
https://www.miataturbo.net/attachmen...ine=1329351369
Total win. I've used these so much that I got two sets of them. Makes life a million times easier when replacing water lines. http://www.harborfreight.com/4-piece...set-65116.html https://www.miataturbo.net/attachmen...ine=1329351369 Also, another win. Not really useful for miatas unless you're replacing your subframe. But if you own a car with FWD/transverse engine, buy it. http://www.harborfreight.com/automot...bar-96524.html |
Originally Posted by ZX-Tex
(Post 835390)
WIN
Heavy Duty hand Riveter http://www.harborfreight.com/heavy-d...tle-66422.html https://www.miataturbo.net/attachmen...ine=1329319619 I needed to install some larger rivets that were slightly too big for my small hand riveter so I picked up one of these. Works great. I have used it with aluminum rivets with no problems. The collection bottle seemed goofy at first but if you are installing a lot of rivets it is actually nice to have. |
Originally Posted by Fireindc
(Post 835410)
FAIL - pneumatic brake bleeder.
https://www.miataturbo.net/attachmen...ine=1329322498 It actually DID work, but broke and was actually PUSHING air into the ------- brake lines by the fourth caliper. This was on a 240sx with ABS, and it actually worked well until it failed and did the OPPOSITE of what i wanted. How on earth did you break it? It's just a venturi that draws a vacuum. ??? |
1 Attachment(s)
WIN - got a drill press? You want this.
http://www.harborfreight.com/9-inch-...amp-36221.html https://www.miataturbo.net/attachmen...ine=1329408897 |
Originally Posted by hornetball
(Post 835741)
I've got one of these and use it all the time. Works great. Very sturdy.
How on earth did you break it? It's just a venturi that draws a vacuum. ??? As for why exactly it started pressurizing the line instead of creating a vacuum on it, i'm not really sure. I'll ---- with it some more later and update if i can get it to work again - although i tried to fix it for about 10 mins before saying ---- it and doing it the old fashioned way. |
Do they have a bead roller for intercooler pipes? I can't seem to find anything with the search terms I'm trying.
|
Originally Posted by curly
(Post 835987)
Do they have a bead roller for intercooler pipes? I can't seem to find anything with the search terms I'm trying.
|
Yeah, I was looking for a bead roller too. They have a general panel-type roller. It didn't look like it would work well on tubes.
|
Originally Posted by Fireindc
(Post 835982)
I do know that some brake fluid got sucked through, and melted the little plastic balls that were in the exit chamber for the air, although im pretty sure those were just to muffle the sound- so i doubt that was the issue. It kept clogging the little hole for whatever reason, and instead of flowing out of it and creating a vacuum it pressurized it and flowed backwards pushing bubbles up into the brake line.
As for why exactly it started pressurizing the line instead of creating a vacuum on it, i'm not really sure. I'll ---- with it some more later and update if i can get it to work again - although i tried to fix it for about 10 mins before saying ---- it and doing it the old fashioned way. Thanks for the heads up on this. I've done several cars with mine (brakes and clutch lines). So far so good. But I didn't realize that the outlet was succeptible to clogging. Definitely keep an eye on that. |
HF 6 inch Digital Calipers
http://www.harborfreight.com/6-inch-...per-47257.html FULL OF GLORIOUS WIN!!!!!!! As a mechanic, my co-workers give me crap about my harbor freight purchases. But, with this item I turned the tables on them. :D Upon closer inspection of my coworkers matco, cornwall, and snap-on calipers, I realized the computerized screen that does the actual measurements, is the same on all the calipers. :giggle: $9.99 with coupon HF calipers = $119.99 matco calipers. :rofl: |
Years ago, I bought a set of those Harbor Freight calipers, Centech or whatever, and they have been fine. I also bought a Harbor Freight knockoff of a Fluke digital multimeter (DMM); the HF DMM has also been great for years.
The DMM is similar to this one, but looks more like a Fluke. http://www.harborfreight.com/ac-dc-d...ter-37772.html |
Originally Posted by 2ndGearRubber
(Post 836393)
HF 6 inch Digital Calipers
http://www.harborfreight.com/6-inch-...per-47257.html FULL OF GLORIOUS WIN!!!!!!! As a mechanic, my co-workers give me crap about my harbor freight purchases. But, with this item I turned the tables on them. :D Upon closer inspection of my coworkers matco, cornwall, and snap-on calipers, I realized the computerized screen that does the actual measurements, is the same on all the calipers. :giggle: $9.99 with coupon HF calipers = $119.99 matco calipers. :rofl: edit: actually, jokes still on your coworkers, for spending so much and thinking they're worth a damn. |
Originally Posted by curly
(Post 836736)
That's because real machinists use dial calipers or vernier calipers. Digital calipers are a joke no matter the brand. Jokes on you buddy.
:facepalm: Phuulleeeeeeeease. I do not want to jack my own thread, but I cannot let this one slide. |
Where did you get the coupon? I need to buy this to measure teeth.
Originally Posted by 2ndGearRubber
(Post 836393)
HF 6 inch Digital Calipers
http://www.harborfreight.com/6-inch-...per-47257.html FULL OF GLORIOUS WIN!!!!!!! As a mechanic, my co-workers give me crap about my harbor freight purchases. But, with this item I turned the tables on them. :D Upon closer inspection of my coworkers matco, cornwall, and snap-on calipers, I realized the computerized screen that does the actual measurements, is the same on all the calipers. :giggle: $9.99 with coupon HF calipers = $119.99 matco calipers. :rofl: |
Originally Posted by ZX-Tex
(Post 836744)
Then I suppose the machinists where I work that build ridiculously amazing parts out of very expensive materials for very tricky NASA space instruments, and could machine circles around anyone here I'll bet, are not 'real' machinists then. I'll be sure to tell them they all suck when I see them again on Monday. And to think they had me fooled all these years.
:facepalm: Phuulleeeeeeeease. I do not want to jack my own thread, but I cannot let this one slide. The fact is I've NEVER seen anyone beyond a machinist with 1-2 years experience use them. I made a statement from my personal experience, please excuse my mistake. Are they using these digital calipers for <.001 tolerances or are they using mics? Ask them what they think of digital micrometers. |
Originally Posted by kenzo42
(Post 836756)
Where did you get the coupon? I need to buy this to measure teeth.
BTW Curly: We use them for measuring rotors, etc. not machine work. |
Originally Posted by curly
(Post 836766)
If they use them and can use them that well then great, I honestly don't mind using digital calipers myself for the imprecise projects I do.
The fact is I've NEVER seen anyone beyond a machinist with 1-2 years experience use them. I made a statement from my personal experience, please excuse my mistake. Are they using these digital calipers for <.001 tolerances or are they using mics? Ask them what they think of digital micrometers. If they aren't getting them calibrated annually, it's not the micrometer's fault. That goes for digital, analog-vernier, or a yardstick. Maybe it has more to do with the quality digital version being 4-10x the cost of the vernier one... Are these same guys that eschew digital micrometers also using non-digital mills and maching centers? |
Originally Posted by y8s
(Post 836825)
Are these same guys that eschew digital micrometers also using non-digital mills and maching centers?
|
Yeah their cnc mills and manual mills are all digital readouts to .0001 or better. Of course for sub mi work they will use micrometers or the like, or the CMM (digital) which is really accurate.
Right tool for the right job. Digital calipers do not suck by default. For most of DIY types they are fine. Let's get back on topic. |
Just had the 8 drawer wooden chest delivered. Got it for just under 70 bucks shipped to my door, and that was after NYS tax (the bastards).
http://www.harborfreight.com/eight-d...est-94538.html Lighter than I expected, but looks fairly well made. Certainly not a Gerstner, but at less than a quarter the price, it's decent enough. It's going to be used to hold my calipers, spare lathe and mill bits, and other associated tooling. The lathe and mill have a large, dedicated bench, and this will sit between them and never be moved. Drawers are kinda shallow for mechanics tools, but it's not really made for that. For the small tools I use on the lathe and mill, it should do just fine. |
All times are GMT -4. The time now is 03:58 PM. |
© 2024 MH Sub I, LLC dba Internet Brands