how strong is wood?
"how strong is wood? "
Hustler will be along to tell you his can punch through armor plate after satisfying 2 women.
I second (or third) the suggestion to break them up. I destroyed an old step foundation in preparation for a porch. Took a 16 pound sledge, and just hammered away.
Jackhammers are easy to rent, though. Home Depot should have them.
Hustler will be along to tell you his can punch through armor plate after satisfying 2 women.
I second (or third) the suggestion to break them up. I destroyed an old step foundation in preparation for a porch. Took a 16 pound sledge, and just hammered away.
Jackhammers are easy to rent, though. Home Depot should have them.
Joined: Jun 2005
Posts: 19,338
Total Cats: 574
From: Fake Virginia
ok I'm going to preface this by saying not to do it based on my calculations. it is at your own risk. i am not liable. etc etc disclaimer disclaimer. it's dangerous and stuff.
without knowing the specific species of wood and condition of the posts, it should hold 500 lbs and only deflect about a 1/2 inch. if your beam has any defects or holes or knots, all bets are off.
make sure you get some video to put on failblog if you try this though.
without knowing the specific species of wood and condition of the posts, it should hold 500 lbs and only deflect about a 1/2 inch. if your beam has any defects or holes or knots, all bets are off.
make sure you get some video to put on failblog if you try this though.
ok I'm going to preface this by saying not to do it based on my calculations. it is at your own risk. i am not liable. etc etc disclaimer disclaimer. it's dangerous and stuff.
without knowing the specific species of wood and condition of the posts, it should hold 500 lbs and only deflect about a 1/2 inch. if your beam has any defects or holes or knots, all bets are off.
make sure you get some video to put on failblog if you try this though.
without knowing the specific species of wood and condition of the posts, it should hold 500 lbs and only deflect about a 1/2 inch. if your beam has any defects or holes or knots, all bets are off.
make sure you get some video to put on failblog if you try this though.
I'm thinking these will make great yard art. Bases for a picnic table? Use the flat tops as lawn chairs?There's gotta be some redneck way to use them that'll be easier than getting rid of them.
Thread Starter
Elite Member
iTrader: (3)
Joined: Oct 2004
Posts: 2,494
Total Cats: 0
From: lansdale PA
i'm not digging any more holes. the whole reason i had to get these out of the ground was that they weren't put below the frost line and were heaving out of the ground making the roof over my porch crooked. My soil in my backyard is sticky *** clay and once you get down to the 3' mark it's all rock, not fun....no more holes than necessary.
Then drill holes and brake up with BFH
__________________
Best Car Insurance | Auto Protection Today | FREE Trade-In Quote
__________________
Best Car Insurance | Auto Protection Today | FREE Trade-In Quote
Thread Starter
Elite Member
iTrader: (3)
Joined: Oct 2004
Posts: 2,494
Total Cats: 0
From: lansdale PA
here's my solution, took the truck to work and grabbed this after off craigslist, this made more sense in terms of future uses and mobility. won't get a chance to do it till after i get back from california. what did i ever do before i had a truck, seriously i don't think i could ever be without one again
It's how far down the ground freezes in the coldest part of the year. Typically up to 36" here in upstate NY. Codes require you to plant footers down below that, so the ground freezing doesn't force the footer up, heaving the structure.
here's my solution, took the truck to work and grabbed this after off craigslist, this made more sense in terms of future uses and mobility. won't get a chance to do it till after i get back from california. what did i ever do before i had a truck, seriously i don't think i could ever be without one again
Thread
Thread Starter
Forum
Replies
Last Post
russian
Miata parts for sale/trade
6
Oct 8, 2015 03:01 PM
mdkimbal
Meet and Greet
10
Sep 8, 2015 09:09 AM








