braineack built ms3. alternator control? help im stranded
So I thought I had a bad battery recently, same time I installed my ms3. Acid was everywhere and smelled horrible.
I replaced yesterday, drive about 15minutes and the same exact thing has taken place. Checked the base tune I've barely modified and the alternator control is off. As soon as the car is started, it goes from 12.7v to 17v and that is when acid starts spurting out of the battery case. I've been in a parking lot try to get settings online. I copied one to the best I could but for the control output I do not have pwm3. I have it on high frequency .... Like the thread said. I tried output nitrous1 and another and nothing Changed. Battery jumps to 17v the second the car is turned on. This is a 2000 nb with a braineack built ms3. Can anyone help??! |
You have like the worst luck with MS's out of anyone I have seen. This sounds like something is going wrong with either the alternator, or alternator control on the MS.
|
Well, if alternator control is off like you say, then what you're seeing is normal. As soon as you start the car, the alternator will try to charge as high as it can if you're not controlling it.
Either switch on alternator control or install a separate controller board. |
I do have the worst luck. I fix one issue to discover another haha. And I turned it on as I said earlier. Nothing happened. That's why I made the thread.
I know it's the settings because everything functioned properly when the stock ecu was in. I'm asking for settings for alt control as there is a lot of variables |
1 Attachment(s)
This is a screen shot of my alternator settings. This was a basemap from Braineack being used to control my 99. I think your settings should be very close if not exactly the same as this.
https://www.miataturbo.net/attachmen...ine=1440700236 |
Originally Posted by shuiend
(Post 1260846)
This is a screen shot of my alternator settings. This was a basemap from Braineack being used to control my 99. I think your settings should be very close if not exactly the same as this.
https://www.miataturbo.net/attachmen...ine=1440700236 |
Originally Posted by sickmiatabra
(Post 1260851)
I just input these exact settings and nothing happened :( jumped and help at 17.8 volts for the 20 seconds I let it run. Fml
|
Originally Posted by shuiend
(Post 1260855)
Did you burn the settings, then power cycle the MS?
|
i leave my desk for one hour...
|
Originally Posted by Braineack
(Post 1260875)
i leave my desk for one hour...
|
Originally Posted by shuiend
(Post 1260846)
This is a screen shot of my alternator settings. This was a basemap from Braineack being used to control my 99. I think your settings should be very close if not exactly the same as this.
https://www.miataturbo.net/attachmen...ine=1440700236 https://cimg1.ibsrv.net/gimg/www.mia...05e87cee96.jpg Hi guys im having the same of the same odd voltage spike issues and I fixed it before but don't remember what setting I chose. These are my options now. Can you assist? |
Originally Posted by atli126
(Post 1576112)
Hi
Hi guys im having the same of the same odd voltage spike issues and I fixed it before but don't remember what setting I chose. These are my options now. Can you assist? https://cimg0.ibsrv.net/gimg/www.mia...3a0e48e45d.jpg |
Originally Posted by irodd
(Post 1576192)
The issue is I don't have the ability to choose that option. Maybe my ms3 needs a firmware update? |
Originally Posted by atli126
(Post 1576405)
The issue is I don't have the ability to choose that option. Maybe my ms3 needs a firmware update?
|
Originally Posted by irodd
(Post 1576406)
try "closed loop field control"
Should have said that. I tried that too. Here is my new thread https://www.miataturbo.net/megasquir...1/#post1576398 |
How old is your MS3? If you have a firmware older than V1.3.0 IIRC the alternator control wasn't available so you most likely have an separate alternator control board.
|
Originally Posted by atli126
(Post 1576407)
Should have said that. I tried that too. Here is my new thread https://www.miataturbo.net/megasquir...1/#post1576398
I can select that but it still Happens plus I don't know what the correct settings it should be for it? |
Originally Posted by Reverant
(Post 1576416)
How old is your MS3? If you have a firmware older than V1.3.0 IIRC the alternator control wasn't available so you most likely have an separate alternator control board.
Hmm I'm not sure. How can I find out? Is it in the settings in tuner studio? |
Based on your reply, I won't recommend trying to update the firmware yourself, find a reputable tuner who can update the firmware to a stable version (hint: V1.4.0 has been the most stable for me so far) and tune your car.
|
Originally Posted by Reverant
(Post 1576487)
Based on your reply, I won't recommend trying to update the firmware yourself, find a reputable tuner who can update the firmware to a stable version (hint: V1.4.0 has been the most stable for me so far) and tune your car.
Thanks ill get with my buddy who tuned it for me. They did recommend I try to update the firmware but be cautious. Thanks, Bret |
All times are GMT -4. The time now is 04:34 AM. |
© 2024 MH Sub I, LLC dba Internet Brands