Originally Posted by andym
(Post 1501309)
I was looking into using this gauge
https://perfecttuning.net/en/gauge/5...sal-gauge.html Possibly coupled with the mslabs canbus wideband controller . Unsure if I want to pursue the canbus wideband controller but for sure I was interested in that gauge. I guess I wanted to know if it would limit me in the future as to what I could use. |
CAN is a multidrop bus
|
So I've followed what was said here in terms of settings and hooking it up and Im still not getting connectivity from the wideband to the ms3propnp, is there something else that I could be missing?
|
Sub'd. Getting ready to connect AEM 30-0300 to a can module & MS3 pro w/FW 1.4.1
|
Originally Posted by DBXJ
(Post 1501786)
So I've followed what was said here in terms of settings and hooking it up and Im still not getting connectivity from the wideband to the ms3propnp, is there something else that I could be missing?
|
Originally Posted by wackbards
(Post 1501795)
Sub'd. Getting ready to connect AEM 30-0300 to a can module & MS3 pro w/FW 1.4.1
MSLabs CAN Wideband Module |
Ok, good stuff. I bought it though TSE, so I'm aware of what's posted there. I'm still just casting a wide net and trying to learn from what other folks are doing to get this set up right.
|
Originally Posted by wackbards
(Post 1501802)
Ok, good stuff. I bought it though TSE, so I'm aware of what's posted there. I'm still just casting a wide net and trying to learn from what other folks are doing to get this set up right.
|
Originally Posted by SpartanSV
(Post 1501800)
Post your tune so I can see your settings.
I'm still new to the MS setup and have not done anything with the car other than first start. |
Well we actually got it sorted, the gauge wasn't sending any kind of signal out
|
Did you guys use termination resistor on the AEM end?
|
Originally Posted by irodd
(Post 1502665)
Did you guys use termination resistor on the AEM end?
|
Does the newer MTX-L Plus work with the MSLab CAN Module?
|
Thanks to all that posted their settings! I am also doing an 30-0300 on an MS3PRO PnP and there's still one setting I'm a bit confused about. Under "calibrate AFR table", what are you putting into "EGO sensor"? Since the AFR gauge will be using CanBus now, and not an 0-5v signal, is this even relevant? Should I select the blank option in the pull down and write that to the controller?
|
Originally Posted by BimmerSchnitzel
(Post 1587342)
Thanks to all that posted their settings! I am also doing an 30-0300 on an MS3PRO PnP and there's still one setting I'm a bit confused about. Under "calibrate AFR table", what are you putting into "EGO sensor"? Since the AFR gauge will be using CanBus now, and not an 0-5v signal, is this even relevant? Should I select the blank option in the pull down and write that to the controller?
|
It's been a few months into 2021, are there any new info updates on OP's particular wideband? I moved away from the MTX I bought a few years back and was thinking about this one for my MSM project too. From what I'm gathering it's a lot more straight forward of a process than using the older analog widebands?
My apologies if my questions have super obvious answers, or are too general for a useful answer. I've been out of the game for a LONG time on my build and I'm trying get back into the hang of things 😂 |
(Not OP) I can confirm using AEM X-Series via CAN w/ MS3ProPnP works great. 9/10 would recommend, only caveat being using AEM Net precludes you from using other CAN devices with MS3 IIRC
|
One day these semiconductor shortages will end and this will go back in stock (woo native wideband). I've been trying to buy one for about a year now...
https://www.14point7.com/products/spartan-3-adv |
Originally Posted by cpierr03
(Post 1594763)
(Not OP) I can confirm using AEM X-Series via CAN w/ MS3ProPnP works great. 9/10 would recommend, only caveat being using AEM Net precludes you from using other CAN devices with MS3 IIRC
|
Hello, I hope you can help me:
I have this configuration with the FW 1.5.2RC16 and the wideband does not read me I have tried changing the CAN ID of the wideband and it doesn't work either. what am I doing wrong? https://cimg7.ibsrv.net/gimg/www.mia...cb67c7335f.jpg |
All times are GMT -4. The time now is 05:59 AM. |
© 2024 MH Sub I, LLC dba Internet Brands