Can't open files with Tuner Studio 0.999.9b
I upgraded and now, when I open an MSQ I get this error:
http://i55.tinypic.com/iefm6f.jpg So I click no and get "Unexpected error occured opening this project". I can close that window, then open my .msq What is the difference between a project and an MSQ? I keep all my data in a directory on the desktop since that's just about the only thing I use that computer for (aside from interspieces porno). |
Interspieces porno is highly under rated but I'm flaky myself with TS Lite.
I did the whole "aquire" thing initially where it shakes hands with the ECU etc but then it seemed a bit convoluted. Since I have good old drop out prone Megatune I never pressed the issue... |
trey, have you upgraded firmware lately? the new install may not have access to your current firmware or the project you last used.
project: car definitions, dashboards, settings, etc. msq: just the shit that loads onto the megasquirt box. |
You will need to set up your project first.
File > Project > New Project http://www.diyautotune.com/tech_arti...dio_how_to.htm |
|
It's a bug with them disabling communications. I can't find it now but there was a thread on msextra about it. It's already fixed and will be in the next version.
|
Thanks everyone. It looks like FatKao may be on to something. It's no big deal for me, but I'm trying to get Machismo and Johnwag set up.
|
|
Ok, I tried to adjust some things on my car today, and following the instructions from Ben, TS hangs on the "finish" step and will not create a new project. It also will not connect to the controller at all.
|
I just uninstalled TunerStudio from my laptop and reinstalled the newest version off the EFI Analytics website. I can't replicate either of your problems. The version I just installed is 0.999.9b_RC4 from this site:
http://www.tunerstudio.com/index.php...d=26&Itemid=40 |
I'm going to remove and reinstall...then leave for my race.
|
It looks like there are 2 problems here.
One like stated above, you need to create a Project to communicate with your controller. Double clicking an msq creates a temp project for viewing, but is not intended to communicate with the controller. That is why comms is disabled now if you select to use a Temp project. Secondly, 0.999.9b had a bug causing the "Unexpected Error" message when opening a Temp Project. 0.999.9h has this corrected. |
I'm on .9h, get with it!
your welcome for the useless post |
Originally Posted by lt401vette
(Post 688813)
It looks like there are 2 problems here.
One like stated above, you need to create a Project to communicate with your controller. Double clicking an msq creates a temp project for viewing, but is not intended to communicate with the controller. That is why comms is disabled now if you select to use a Temp project. Secondly, 0.999.9b had a bug causing the "Unexpected Error" message when opening a Temp Project. 0.999.9h has this corrected. |
I have it, might test it out tomorrow.
|
Originally Posted by djp0623
(Post 688822)
I'm on .9h, get with it!
your welcome for the useless post |
Originally Posted by y8s
(Post 688874)
dont troll the author of the software.
|
my MS3 is still on v.28...I think there's been like 10 versions since. Granted I haven't driven the car either.
|
I'm waiting on TiAL to send me CHRA bolts before I drive the car again.
|
I'm running an Rev built MS3 Basic. Getting the same "Unexpected Error occurred opening project." Any advice on what I should change? Recently upgated TunerStudio v3.0.12
|
All times are GMT -4. The time now is 10:33 PM. |
© 2024 MH Sub I, LLC dba Internet Brands