Can't rev over 6k - Miata Turbo Forum - Boost cars, acquire cats.

Welcome to Miataturbo.net   Members
 


MEGAsquirt A place to collectively sort out this megasquirt gizmo

Reply
 
 
 
LinkBack Thread Tools
Old 05-05-2012, 09:02 PM   #1
Elite Member
Thread Starter
iTrader: (10)
 
Join Date: Oct 2008
Location: Seattle, Wa
Posts: 1,780
Total Cats: 30
Default Can't rev over 6k

This isn't on a miata, but I figured there are enough MS users on here that perhaps a solution will fall out .

Car:
240SX w/ KA24DE swap.
Turbocharged, running MS2extra 3.1.0.
Single coil, stock cam sensor providing trigger input.

Nothing fancy, just a pretty much 'by the book' MS2 build w/ EBC.


The problem:
The damn thing won't rev over 6k under load. It pulls fine under any amount of boost, but around 5500 it starts to slow down, and hits a wall at right about 6k. Free revving doesn't exhibit this issue.

On the dyno, the onboard WB sensor goes full rich when this happens. Tried leaning it out, the result was knock and a severe lean spike (in other words, it didn't smooth out, it was one extreme or the other).

Things I've checked:
Fuel pressure is good.
Fuel injectors are 560cc subaru injectors and have been recently cleaned.
Tried swapping coils (MSD Blaster SS and stock)
Changed plugs and re-gapped to .028
Swapped wires.
Swapped distributor.
Checked base timing.
Tried dwell from 2.5-4.5ms


Things that confuse me:
The WB on the dyno read full rich when this happened. I thought that perhaps the injectors were going static early and pissing fuel.

Checking the duty cycle shows ~60% at 6k and the AEM WB reads fairly rich(~10.9) with big jagged peaks. Before this it was at 11.1-11.5:1.

Duty cycle seems a bit high to me for 5psi.


So, Bros. Any ideas? I'm attaching a recent .MSQ and a few logs. Lets touch tips and figure this out .
Attached Files
File Type: msq CurrentTune.msq (76.8 KB, 55 views)
File Type: msl 2012-05-04_19.48.22.msl (150.0 KB, 53 views)
File Type: msl 2012-04-21_14.07.58.msl (1.02 MB, 52 views)
Jeff_Ciesielski is offline   Reply With Quote
Old 05-06-2012, 04:14 AM   #2
Supporting Vendor
iTrader: (10)
 
Reverant's Avatar
 
Join Date: Jun 2006
Location: Athens, Greece
Posts: 5,440
Total Cats: 197
Default

Update the firmware.
Reverant is online now   Reply With Quote
 
 
Reply

Related Topics
Thread Thread Starter Forum Replies Last Post
MS PNP requires reading and following directions??? satisfied MEGAsquirt 141 10-06-2015 11:44 AM
Back to Stock Part Out!! Turbo Parts, MS2 Enhanced 01-05, Suspension, and MOAR! StratoBlue1109 Miata parts for sale/trade 16 10-02-2015 10:39 AM
Another Alternator thread ihiryu General Miata Chat 9 09-28-2015 11:22 AM
Flex fuel settings on Rev build MS3 PnP for NB8B nitrodann MEGAsquirt 0 09-07-2015 09:01 PM


Thread Tools

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Trackbacks are Off
Pingbacks are Off
Refbacks are Off



All times are GMT -4. The time now is 04:08 AM.