EBC Configuration Error
1 Attachment(s)
I am trying to set up ready to go from MBC to EBC however I am getting a Config error when I turn on Boost Control Settings.
ECU - DIYPNP ECU Wiring: PA0 (behind db9) to IN on boost circuit OUT on boost circuit to pin on db15 set boost control pin in TS to PA0 No matter what I do in the settings I keep getting a config error like this: https://www.miataturbo.net/attachmen...ine=1327152689 Do I have the output port setting wrong or is it something else I have done? If I turn the boost control setting to off the config error problem goes away..... Barry |
The PA0 port in the output port settings needs to be disabled.
|
Thanks Dimitris, that has cured the config problem, but I am not confident that MS is controling the boost solenoid (brought from diyautotune), with everything turned on (open loop, control duty table set to '30' throughout the table to test), if I disconnect the solenoid from the 12v supply and reconnect it should I hear the solenoid kick in? There is no noise whatsoever, is there a way of testing that MS is controling the solenoid?
Cheers Barry |
Cancel that, its working. For some reason, the solenoid doesent operrate with just the ignition on (12v supply from small blue connector by diagnostics box) but if I start the car it clicks in.
Measured the voltage at the 12v supply with ignition on and its only reading 11.1v so I assume I have a battery problem and the solenoid only works with 12v? Barry |
its 12v on each side with a soke to gnd on the ecu side.
Just throw 100 in all target cells and see if you get more boost then usually, if it works the turbo will spin alot quicker, if it doesn't you will see wastegate, if it doesn't swipe all cells and put 0 in them. Careful now make sure you have an overboost cut active. The blue connector works fine for 12v. I use it with my solenoid and EBC circuit |
Originally Posted by Techsalvager
(Post 824113)
its 12v on each side with a soke to gnd on the ecu side.
Just throw 100 in all target cells and see if you get more boost then usually, if it works the turbo will spin alot quicker, if it doesn't you will see wastegate, if it doesn't swipe all cells and put 0 in them. Careful now make sure you have an overboost cut active. The blue connector works fine for 12v. I use it with my solenoid and EBC circuit Barry |
Where do you find this in TS
"The PA0 port in the output port settings needs to be disabled" Is it a TS setting the only thing I can find is boot control location i can make that pa0? |
Extended -> Output port settings
|
see BAZ's screenshot.
|
K. So then I have not idea why I was getting an error. if you have ebc turned on and no ebc hooked up does that normaly mean no spark cause thats what happened to me or it was the cas which i changed same time as I changed the ebc to no. by the way I never indicated it was yes that was the base tune as I loaded it from diyauto
|
because DIYs basemap has that error on it.
|
Originally Posted by Braineack
(Post 825821)
because DIYs basemap has that error on it.
|
9093 iirc
|
Some info on what error is on the 9093 base map would be good....
|
So is the error that ebc is turned on or that if it is that there is conf error or does ebc not work at all.
How do i fix this. I have ebc sol in car just have not run the hose or connected a 12 keyed source. Will soon thou what can I expect will it work? |
the error is that on the basemap the boost control is deafulted on and it happens to be selected to a output that's already in operation.
Simply turn boost control function to OFF, or select the proper output that corresponds to what you acutally put it on. The conflict is that two things are using one output. |
All times are GMT -4. The time now is 02:25 PM. |
© 2024 MH Sub I, LLC dba Internet Brands