Launch Control
So my launch control was just cutting Spark only but now is cutting spark and fuel outta no where. I went into my msq and confirmed that Spark only is selected. Im thinking I may need to reload the firmware? Any Ideas? I tried switching to Spark and Fuel and back to Spark Only. It is still cutting spark and fuel.
|
Could be some other fuel cut setting kicking in; can you post an MSQ and data log?
|
Yeah later on tonight I can. What else would be cutting fuel? I didnt have this problem till recently and the tune wasnt changed.
|
Do you by any chance have a 2 step setup thats cutting both spark and fuel?
|
Figured it out just to update the thread. I had some how had incorporate AFR on when I updated firmware. I turned it off problem solved and retuned just for safe measure.
|
Originally Posted by ScottyP3821
(Post 1110554)
Figured it out just to update the thread. I had some how had incorporate AFR on when I updated firmware. I turned it off problem solved and retuned just for safe measure.
it's also not a setting that should played with willy nilly... So you're suggesting that you used to sit on the lauch limiter and blow fireballs out the back of the car, but now it suddenly stopped, but then you completely changed your fueling algorithm and you now have fireballs again to impress your friends? |
After I updated the firmware I tuned my fuel table at the same time. I went to go use LC and I noticed I was leaning out all the way. I went through my whole tune and noticed it was on and I never remembered having it on in the past. So I turned it off and retuned my fuel. Now everything's is good under LC and I'm not leaning out. Something about launching lean doesn't sit well with me. I sort of understand it was changing my algorithm as when I changed my LC settings my afr acted different as well as when under load my afrs were not as rich as before and I would not go as lean on decell. If I'm wrong please correct me so I can better understand. Thanks.
|
Are you running a PNP or the diy ms? I'm truing to figure out lc issues on my pnp2.
|
Originally Posted by zero415
(Post 1112034)
Are you running a PNP or the diy ms? I'm truing to figure out lc issues on my pnp2.
|
Originally Posted by ScottyP3821
(Post 1112170)
Pnp with 1.5b board. What year? Does it have cruise control?
|
Originally Posted by ScottyP3821
(Post 1112170)
Pnp with 1.5b board. What year? Does it have cruise control?
Originally Posted by triple88a
(Post 1112185)
Isnt CC completely independent from the ECU?
I'm going to try that when it warms up and see if that helps. |
Yeah you need to unplug two little white connectors on top of the tranny. At least thats what I had to do on my 1.8.
|
Well thanks for confirming. Tomorrow is going to be a nice day so I'll do it then.
|
Originally Posted by ScottyP3821
(Post 1112277)
Yeah you need to unplug two little white connectors on top of the tranny. At least thats what I had to do on my 1.8.
|
Originally Posted by zero415
(Post 1112382)
Whats the best way to get to the connectors? from the top next to the shift leaver or under the car?
|
Question for you all... How do you determine your launch timing and your flatshift timing? How about what rpms for flatshift and launch?
|
My flatshift rps are at 4500k. and my Launch is at 3500k which im thinking of lowering and I am timed to 5 degrees. Thats going off the top of my head. Im not at my tune right now. I followed this guide How to 2 set up step rev limiter 2step | Tuning Launch Control
|
Well I finally went up under and unplugged both white connectors but still launch control didn't work. Are there any specific instructions for setting up LC on a 1.6?
|
Just a thought..
Becareful of spark only cut on flatshift I cut 5 of 7 sparks and hydrolocked my engine at about 4000rpm and 100mph and bend 2stock rods. Had to rebuild the engine. I will never fuck with launch control or flatshift again |
Originally Posted by zero415
(Post 1114023)
Well I finally went up under and unplugged both white connectors but still launch control didn't work. Are there any specific instructions for setting up LC on a 1.6?
Originally Posted by Lloyd_D
(Post 1114205)
Just a thought..
Becareful of spark only cut on flatshift I cut 5 of 7 sparks and hydrolocked my engine at about 4000rpm and 100mph and bend 2stock rods. Had to rebuild the engine. I will never fuck with launch control or flatshift again |
All times are GMT -4. The time now is 05:37 AM. |
© 2024 MH Sub I, LLC dba Internet Brands