|
Alright here we go, I finally get to play with it again.
I am going to go back through the maps check settings and then give her a crank with the new GM IAT Sensor now being used. I guess we shall see just what happens. |
Alright it starts right up and runs but the idle is nuts again jumping all over, I did a data log the new GM IAT seems to be right on the mark.
So once I can nail this idle down to normal I can take her out and start fine tuning. Seems to be rich right now. |
Alright I have been driving the car the past two nights, great results so far.
I have a stable idle (considering I unplugged the IAC since no one has any answers for the issues I am having) and AFR's are looking good. I have not really pushed it but come tomorrow I will do some freeway runs and push her and then post up my tune. Gets me around town for the time being quite well. |
Hey guys, been making some progress and was going to update the first to posts but the edit button is not showing, hopefully a Mod can help me with that so I can reorganize the thread with a lot more information and a little better layout as well as most importantly some hopefully helpful information.
Thanks! |
What is "safe" 100kpa AFR in a track car at 9:1 static compression or even 10:1 compression?
|
Originally Posted by hustler
(Post 669485)
What is "safe" 100kpa AFR in a track car at 9:1 static compression or even 10:1 compression?
I'm around 12.8-13, 9:1. |
Originally Posted by FatKao
(Post 649911)
1) You need to build the tach output circuit if you haven't already done it. Not sure the differences between NA and NB cars. There should be enough in my thread to get you going. Read the whole thing because I didn't quite do it right the first time out.
2) You should be using Inverted if you're using Joe Perez's spark circuit (you should be using Joe Perez's spark circuit) non-inverted if you just have the outputs going straight from the MS. Using the wrong one can quickly damage your coil packs. Here is my latest tune. Mod list is in the other thread. Keep in mind that I don't have AC/PS or care about streetability so I just have the idle screw set to idle the car at 1k and don't control the IAC at all. I am not using the IAC either, hows your idle look when you let off does it stabilize quickly? |
It bounces once or twice, I had to put a block of I think 16* or 17* cells around the idle area to prevent it from osculating forever. The theory was that the spark advance moving up and down a few degrees was causing the idle to cycle. Looks like that was the case.
My only outstanding issue is that the engine bogs for a second when hitting the gas from idle. |
I have had some good luck getting everything dialed in.
The Cold Starts are ok, Idle is hit or miss I will continue working on it but I am pretty damn close it idles just not 100% of the time 85% of the time it will idle the rest it hunts occasionally. I will post it up as soon as I am done. But shortly I think I will be going to the 550cc Injectors and running meth while I prep to run boost. |
Originally Posted by 90R
(Post 649747)
the base map from DIY is scaled for FI. I have a decent tune for NA I'll post later. It's still lacking on the cold start but should get you running.
|
Originally Posted by JustinHoMi
(Post 676374)
You're running 30deg of timing at idle??
|
Wow, that's the worst timing map I've seen in a while, must be as lumpy and rough as hell at low rpm and low rpm and heavy load must knock like fuck.
I've a feeling your timing isn't synced properly, there's no way in hell any MX5 engine I've tuned would idle at 30deg of timing, so I don't see how yours could or would. |
Originally Posted by richyvrlimited
(Post 676808)
Wow, that's the worst timing map I've seen in a while, must be as lumpy and rough as hell at low rpm and low rpm and heavy load must knock like fuck.
I've a feeling your timing isn't synced properly, there's no way in hell any MX5 engine I've tuned would idle at 30deg of timing, so I don't see how yours could or would. it run's fine, idles smooth....don't know what to tell you. |
Double/triple check the sync?
|
Originally Posted by richyvrlimited
(Post 676812)
Double/triple check the sync?
|
| All times are GMT -4. The time now is 02:06 AM. |
© 2024 MH Sub I, LLC dba Internet Brands