1.8 Short blocks/ 99 bare head/ flywheel/ misc parts
Thread Starter
Joined: Oct 2007
Posts: 6,029
Total Cats: 304
From: The coal ridden hills of Pennsylvania
It's time to clean house. It would be cool if somebody would offer me a fair amount and come take everything, but we'll see what happens.
A few years ago I bought this complete 2000 engine. I took it all apart a few months ago, honed the cylinders, and put brand new Sealed Power rings in it. That block with the rotating assembly is sitting on an engine stand, ready to be finished. I have everything to finish this short block, oil pan, brand new tube of Mazda oil pan sealant, balancer, timing gear, factory oil cooler, much more. I even have all the bolts labeled from where I took them off (see cereal box). I'm not interested in shipping this, but I can deliver within reason. $200 NEG.





Also have a 1.8 flywheel. Can get photos and prices upon request.
A few years ago I bought this complete 2000 engine. I took it all apart a few months ago, honed the cylinders, and put brand new Sealed Power rings in it. That block with the rotating assembly is sitting on an engine stand, ready to be finished. I have everything to finish this short block, oil pan, brand new tube of Mazda oil pan sealant, balancer, timing gear, factory oil cooler, much more. I even have all the bolts labeled from where I took them off (see cereal box). I'm not interested in shipping this, but I can deliver within reason. $200 NEG.





Also have a 1.8 flywheel. Can get photos and prices upon request.
Last edited by thirdgen; Dec 11, 2016 at 07:55 PM.
Thread Starter
Joined: Oct 2007
Posts: 6,029
Total Cats: 304
From: The coal ridden hills of Pennsylvania
1 hour east of Harrisburg. Use cabelas hamburg in your gps, you'll be 7 minutes from my house. A decent offer will take everything in 1 trip.
Hey man, just sent this link to a friend looking for an engine. Pm me your phone number with your email abt the turbo stuff and maybe we can figure out a big package deal.
Edit: Just talked to my friend and he's interested in the full motor.
Edit: Just talked to my friend and he's interested in the full motor.
Last edited by ridethecliche; Nov 5, 2016 at 12:03 AM.
Thread Starter
Joined: Oct 2007
Posts: 6,029
Total Cats: 304
From: The coal ridden hills of Pennsylvania
The one that re-ringed is still on my stand, never fired up. Buy it, put a head on it, do a compression test, smile at results. It's brand new.
new bearings as well? shoot me a message via real # probably faster method of communication as I am dead serious about purchasing 8452403358
Thread Starter
Joined: Oct 2007
Posts: 6,029
Total Cats: 304
From: The coal ridden hills of Pennsylvania
Where are you from? No, bearings were fine. Block didn't have issues, when I took this engine apart the cylinders were glazed, so I honed them and re-ringed. That was all.
Last edited by thirdgen; Nov 5, 2016 at 09:31 AM.
Thread Starter
Joined: Oct 2007
Posts: 6,029
Total Cats: 304
From: The coal ridden hills of Pennsylvania
I just PM'd him back with some information and I will email you later with the pictures like I promised. I need to take the time and sit down to create a detailed list for you.
Haha no rush. He just didn't tell me that you guys were already in contact. Sorry for seeming over eager.
Thread Starter
Joined: Oct 2007
Posts: 6,029
Total Cats: 304
From: The coal ridden hills of Pennsylvania
I'm asking $750 neg for both combined. Flawless means brand new, I know these blocks aren't it, but $200 can't cut it.
I could do $500 picked up for them, but $200...I just can't go that low.
I could do $500 picked up for them, but $200...I just can't go that low.





