absurdflow, gt2860, vband, tial, works, rollbar, seat, partout...
 

EDIT: EMAIL ME AT kewilso3@gmail.com WITH ALL QUESTIONS PM's are getting out of control, thanks

ALSO no stock parts for sale!!Raleigh NC.

So I am parting out my 94 miata. The car was totaled a short while ago, and it is gone to the junkyard. I have many of the turbo parts still that were on it. Most have less than 5k miles, all less than 10k. The hardtop has been sold.

Sparco sprint seat SOLD, rails still available

RX7 460cc red top injectors, cleaned/flowed about 2 years ago, plug and play (with tuning of course)

$140 shipped

Stance GR+ coilovers, under 10k miles, scuff on one from wreck, I see no reason it wont work perfectly

$800 plus shipping

Konig wide open - SOLD

Panasport gc8 13x8.5 et11 wrapped in shitty 205/60 tires that have under 3k miles on em. one was bent in the wreck, looks very fixable. 10lb wheels. I can also include hoosier slicks

$600 picked up

Work Meister cr-01, SOLD

Garrett gt2860rs, .60 ar, SOLD


Absurdflow centered low mount SOLD

tial MVS 38mm, SOLD

3" to 2.5" downpipe, SOLD

2.5" mandrel bent cat back with magnaflow straight through muffler

https://www.miataturbo.net/attachmen...ine=1317085777

$250 picked up

Frame rail braces by boundary eng. stainless

$100 picked up

Hard dog hard core single diagonal roll bar, SOLD

Magnecor 8.5 mm plug wires

$60 picked up

FM level 2 clutch and 10lb flywheel, SOLD

miscellaneous things like wideband (200), hoses, fittings, an lines, fm silicone piping (100), coolant reroute things, boost gauge, custom switches, blockoff plates, etc
$$$ may vary come take a look

Sorry i dont have good pics of most stuff, I'll get on it tomorrow after work.

https://www.miataturbo.net/attachmen...ine=1316995629

https://www.miataturbo.net/attachmen...ine=1316995629

Konig wideopen:

http://a6.sphotos.ak.fbcdn.net/hphot..._7534297_n.jpg

http://a8.sphotos.ak.fbcdn.net/hphot..._5265113_n.jpg

Still have the bov? how much

Actually i do, it miraculously survived the front end collision. Its made by FM

$60 shipped i guess

Pm me for the Mani dp and wg. Shipped to 14226

PM sent

which fm silicone pipes do you have?

PM sent

Interested in seat and roll bar. PM to be sent.

How much for the wideband?

Is your potato price inclusive of both housings?

Also interested in seat as well as a few other things! pm incoming.

I didnt know they made more than one set, they look to be from the usual fm2 style manifold, I cut them a bit to use with my setup, cant really see pipes in the pictures but that's what i was going for... should work with about any setup facing the compressor outlet down with addition of a couple straight sections and a hard pipe for bov/iac/iat

200 plus shipping, high price since i may use it again, and it is an analog gauge

yeah sure why not, shipping will just be more, it weighs much more than the stainless housing

I want the metal cup holder. Price shipped to 29414.

Pm'd you on multiple things

Could you post more closeups of the turbo? I'd like to see the compressor inlet and outlet, the 5 bolt turbine housing, turbine impeller, and if possible, caliper measurements of the wheels and the CHRA nameplate.

Thanks.

Can you PM me pics of the coilovers, thanks.

Another PM Sent

PM sent for konigs

Sorry about your leg. Must have been a big hit.