absurdflow, gt2860, vband, tial, works, rollbar, seat, partout...
Thread Starter
Junior Member
iTrader: (4)
Joined: Feb 2009
Posts: 318
Total Cats: 0
From: Raleigh, NC
absurdflow, gt2860, vband, tial, works, rollbar, seat, partout...
EDIT: EMAIL ME AT kewilso3@gmail.com WITH ALL QUESTIONS PM's are getting out of control, thanks
ALSO no stock parts for sale!!Raleigh NC.
So I am parting out my 94 miata. The car was totaled a short while ago, and it is gone to the junkyard. I have many of the turbo parts still that were on it. Most have less than 5k miles, all less than 10k. The hardtop has been sold.
Sparco sprint seat SOLD, rails still available
RX7 460cc red top injectors, cleaned/flowed about 2 years ago, plug and play (with tuning of course)
$140 shipped
Stance GR+ coilovers, under 10k miles, scuff on one from wreck, I see no reason it wont work perfectly
$800 plus shipping
Konig wide open - SOLD
Panasport gc8 13x8.5 et11 wrapped in shitty 205/60 tires that have under 3k miles on em. one was bent in the wreck, looks very fixable. 10lb wheels. I can also include hoosier slicks
$600 picked up
Work Meister cr-01, SOLD
Garrett gt2860rs, .60 ar, SOLD
Absurdflow centered low mount SOLD
tial MVS 38mm, SOLD
3" to 2.5" downpipe, SOLD
2.5" mandrel bent cat back with magnaflow straight through muffler
$250 picked up
Frame rail braces by boundary eng. stainless
$100 picked up
Hard dog hard core single diagonal roll bar, SOLD
Magnecor 8.5 mm plug wires
$60 picked up
FM level 2 clutch and 10lb flywheel, SOLD
miscellaneous things like wideband (200), hoses, fittings, an lines, fm silicone piping (100), coolant reroute things, boost gauge, custom switches, blockoff plates, etc
$$$ may vary come take a look
ALSO no stock parts for sale!!Raleigh NC.
So I am parting out my 94 miata. The car was totaled a short while ago, and it is gone to the junkyard. I have many of the turbo parts still that were on it. Most have less than 5k miles, all less than 10k. The hardtop has been sold.
Sparco sprint seat SOLD, rails still available
RX7 460cc red top injectors, cleaned/flowed about 2 years ago, plug and play (with tuning of course)
$140 shipped
Stance GR+ coilovers, under 10k miles, scuff on one from wreck, I see no reason it wont work perfectly
$800 plus shipping
Konig wide open - SOLD
Panasport gc8 13x8.5 et11 wrapped in shitty 205/60 tires that have under 3k miles on em. one was bent in the wreck, looks very fixable. 10lb wheels. I can also include hoosier slicks
$600 picked up
Work Meister cr-01, SOLD
Garrett gt2860rs, .60 ar, SOLD
Absurdflow centered low mount SOLD
tial MVS 38mm, SOLD
3" to 2.5" downpipe, SOLD
2.5" mandrel bent cat back with magnaflow straight through muffler
$250 picked up
Frame rail braces by boundary eng. stainless
$100 picked up
Hard dog hard core single diagonal roll bar, SOLD
Magnecor 8.5 mm plug wires
$60 picked up
FM level 2 clutch and 10lb flywheel, SOLD
miscellaneous things like wideband (200), hoses, fittings, an lines, fm silicone piping (100), coolant reroute things, boost gauge, custom switches, blockoff plates, etc
$$$ may vary come take a look
Last edited by kewilso3; Oct 6, 2011 at 08:02 PM.
0
Thread Starter
Junior Member
iTrader: (4)
Joined: Feb 2009
Posts: 318
Total Cats: 0
From: Raleigh, NC
I didnt know they made more than one set, they look to be from the usual fm2 style manifold, I cut them a bit to use with my setup, cant really see pipes in the pictures but that's what i was going for... should work with about any setup facing the compressor outlet down with addition of a couple straight sections and a hard pipe for bov/iac/iat
200 plus shipping, high price since i may use it again, and it is an analog gauge
yeah sure why not, shipping will just be more, it weighs much more than the stainless housing
200 plus shipping, high price since i may use it again, and it is an analog gauge
yeah sure why not, shipping will just be more, it weighs much more than the stainless housing
0
Elite Member
Joined: Jul 2005
Posts: 6,420
Total Cats: 84
Could you post more closeups of the turbo? I'd like to see the compressor inlet and outlet, the 5 bolt turbine housing, turbine impeller, and if possible, caliper measurements of the wheels and the CHRA nameplate.
Thanks.
Thanks.
0
