Chucks HUGE PART OUT!!!
 

PAYPAL NOW ACCEPTED

All of these are off/for a 95' Mazda Miata. Local pickup prefered contact me for shipping quotes. EVERYTHING IS BRAND NEW UNLESS LISTED. Most of the pics are in my build thread here. Let me know if you want something specific. https://www.miataturbo.net/forum/t30901/

$2000.00 Firm Fully built engine. 95 block, 99 head, adj cam gear, full Belfab kit, 1mm oversize valves, professional machine work done by Westside Performance, arp head studs, arp main studs, 5-valve job, balanced, block decked and head milled, 9.0 cr ratio, and oil crank scrapper. Stock intake manifold, no exhaust manifold. I paid $2200 for parts not including block and $900 for machine work. Total invested $3100.

SOLD 550cc's Rx-7 Injectors

SOLD Toyota COP's With connectors and wires ready to be put together and installed. Less than 8k miles.

$75 Intercooler 18x12x3 "Brand New"

$300 KYB AGX Struts "Brand New"

$100 Racing Beat springs "Brand New"

$40 Fidanza Short-shifter "Brand New"
http://cgi.ebay.com/ebaymotors/ws/eBayISAPI.dll?ViewItem&ssPageName=STRK:MEWNX:IT&it em=140270673195

$50 Knobmeister Large Black Textured Voodoo 6-spd Shift Knob "Brand New"

$50 Greddy Type RS BOV "Brand New" Knock-off (with flange) "Brand New"

EDIT $70 3x2.5" 90degree elbow, 1x2.5"-2.0" 90degree reducer coupler, 1x2.5" straight coupler, 1x2" t-bolt clamp, and 9x2.5" t-bolt clamps "Brand New"

$200 Greddy Type-S EBC Complete "Used"

$250 SSK 15x7" Rims Black with red lip "Time ATTACK" Comes with hub-centric rings. "Brand New"

$250 Braineack's Megasquirt Setup to run parallel, 4-bar map sensor. "Brand New"

$150 Transmission 5-spd "Good condition"

$500 95' Mazda Miata shell no wheels and interior stripped shown in pictures in other thread. Local Pickup only!

$200 LC-1 With Gauge Reviews: Innovate Standalone Gauge Kit w\ LC-1 & Red DB Digital GaugeDIYAutoTune.com "Brand New"

NEW $100 Complete a/c system (Will not seperate) Compressor, Condensor, Evaporator, Dryer, and all a/c lines

NEW $50 Racing Beat Engine Mounts (40% stiffer than stock) "Brand New"

dibs on MS, pics?

MEGASQUIRT
Attachment 207943


Rims
Attachment 207944

Coils
Attachment 207945

I need you to clear your PM's im trying to send you info!! thanks
Paul

pic of LC-1 as well please??

FYI, you can lift the $500/mo limit from Paypal by confirming your account with your SSN. Takes 30 seconds.

or by becoming a premier member...which is like another percent...but allows credit cards. Depends which restriction it might be from.

Not if the ssn is with another paypal account. And I already added my new bank account to my new account before I knew this. So i'm kindof stuck. So NO PAYPAL you can come by the house anytime.

12700 W FM 1960 #7107, Houston, Tx. 77065

Lived in Houston for 19yrs.

It is a premier account still $500 limit :(

sell wiring for your cops separately?

Only if someone wants the COPS by themself.

ill be in for wiring if you find seller for cops.

PM Sent...

PMed!

Prices are FIRM!

wow I wish I had money, and you're local too.

Might do shocks, short shifter, and COPS next month if they're still around.

Dibs on the injectors if they're the high impedance PnP type.

They are high imp should be PnP but might new different injector clips. Shoot me pm to get contact info.

i want the COPs and wires pm, personal check ok??

All that useless posting finally paid off eh?

I can pretty much guarantee that....

Wish this motor had existed about 4 months ago

Chucky,

Do you have any suspension bits to go with those shocks?

eg: NB mounts, bumpstops etc.

Nope sorry nothing else besides springs. Also if you know anybody in H-town who wants a great beginner miata give them me contact info. Thanks

Talking about the rolling shell?

Lots of SCCA guys supposedly look for nice ones to stitch weld and swap over their parts to.

Will let you know if anyone is looking.

Damn, that motor is tempting and I have the cash...this is dangerous! Did you put it together or did the machine shop? Are there any miles on it yet?

i wish you would be selling this engine just a couple of days ago... i just shelled out quiet a bit of cash on 1.8L :/

could you get me a shipping quote on these to 22207?

^ Those wheels look good...I was thinking they'd look pretty good on my 93LE. I've read conflicting reports of 12.0 or 14.2 lbs/corner. Do you have a scale to check one?

Do you know how much those pigtails cost?
Is there no such thing as 550cc PnP injectors that plug into the stock factory connectors?

Oh and what's the recommended redline on that built motor?

have any 1.8 caliper brackets?

Once again, very interested in motor, did you asssemble or machine shop? Cash in hand. Also,s end me or post a pic of injectors...I will take them if they don't sell.

They are roughly 14.5lbs. Come's with center caps and Hub-centric Rings.

Machine shop installed it. Only thing left is timing belt. Oil pump has been checked and is in good shape. I would recommend water pump since it is easy to get too. Shipping is roughly $300 to most states. No miles still at Machine shop waiting for me to tell them where to ship it.

When they shipped them to me they charged $80. Lets say $70 just to make sure I don't eat it on shipping.

Ok I just checked them they plug into the stock wiring harness no pig tails needed. So PnP!!!

With the upgraded valves springs, and rod bolts it should easily handle 8k however with the stock intake manifold and stock cams probably won't need to. I've heard of people revving them higher though so its up to you.

COPS sold!

I think you can consider the motor sold...I'll pm you...I'll likely just drive over and pick it up. I'll PM you with any further questions.

p51hellfire you pm box is full.

If MS sell falls through, I'll take that as well, I just ordered kit for one, but I have friend that could use it.

So far p51 has first dibs awaiting payment. Also you have a PM.

Ohhhh that thing is mine LOL ......

Understood...never hurts to post though...I have seen many things fall through. I'll call you later today Ted...

If they are purple top I will take them. Can paypal today.

Injectors SOLD

Please send the injectors straight to Deatschwerks for servicing. I filled out the form, scanned and emailed it to your paypal email address.

Thanks,

John

Ready to buy that motor, call me back before my wife changes her mind! :)

how much is shipping on the short shifter?

yo pick up your phone lol!!! I sent you the payment and my address get back to me asap!!! thanks
paul

ooops double post

glad I'm not he only one...I have 2k burning a hole in my pocket! Oh, well...maybe I'll spend it on other upgrades...

I wouldn't damn if I had 2g's I'd be all over it!!!!! but i don't and im just getting the MS and he hasn't been on in two days kinda concerning me, then again I'm a worry wart!!!!

Hey Chuck I am interested in those motor mounts let me know if you still have then and I will send you payment ASAP!

hey im interested in the ssk rims? is there 4 or just 1 or what? if you have 4 ill take em shipped to 94401 thanks

chuck bunch of people want stuff where did ya gooooo.......???

Chuck has obviously entered the twilight zone...and he ain't snapping out of it...

I'm pretty sure he's just got one you postwhoring newb.

Second time just in this thread.

Rlogan,

I was waiting behind you on that motor!!! He said he was getting together with you a couple days ago and would let me know if you didn't take it. Now I know why I haven't heard what happened. Nothing happened.

Maybe he had a change of heart on the partout?!?