Reason for sale: short in wiring burnt up my haltech so this is my semi rage quit.

I am not in the USA but all parts will be shipped via Fedex because I trust no post office. Forgot to say Paypal would be the method of payment PM's on here, whatsapp/telegram 3459260538 are the quickest way to get in touch


First up are some K1 H beams attached to CP stock bore 9:1 pistons, they were run for around 100-120 miles before I spun a bearing. You will need new rings. Sold


JDM Square top, i have drilled and tapped one of the EGR block off plates for 1/8NPT and plugged it. I was using it as the MAP source for the ecu. Comes with a few month old GTX PCV valve Sold








My ITB setup. TechnoToyTuning adapter and 100mm velocity stacks with 4age Blacktop throttle bodies. I have done all the port matching to the head as well as the ITB side. I have also modded the throttle linkage so you get full travel with the stock NB Miata throttle cable as well as added extra vacuum nipples to separate the idle air control from the MAP sensor signal. The adapter was sprayed VHT wrinkle black. $700 shipped

I have a BNIB Pipercross PX600 filter and backing plate that just arrived at the post office. I will throw that in with the above for an extra $125






Lastly my spare BP6D head and valve cover. It has new valve stem seals and the front coolant port blocked off. It will come with one of the earlier Skou spacers, thermostat and a Kia water neck with a -16AN bung welded on (I can cut this off if you wanted) but it is not pictured as it's on the head on the car. $600 shipped


Next week I'll have an ORC 409 single plate clutch off the car. It has about 350 miles on it. (picture is from when I originally installed it) $650 shipped

 

Did you spin a rod or main bearing? If it's a rod can you post a pic if the damage?

 

He clearly states wiring burnt up.

 

He also clearly states a spun bearing. Selling rods, it is logical that buyer asks if said bearing was rod or main.

 

you guys crack me up

 

lmfao

the rods and pistons are sold.

Offers on the rest?

$320 shipped on intake manifold?
$575 shipped on ITBs (650 with the filter?)
The head i don't have that much room on unless you're ok with it coming via the post office

Just got a 370z so it needs some mod loving

 

Don't let this guy's location spook you, I received the rods and pistons in better than advertised condition. This guy is legit.

 

Thanks Bronson

flat top is sold

 

local sale for the car fell through so time for some of the heavier stuff, these I will have to do via USPS as fedex wont do the shocks for some reason.


Tein MonoFlex coilovers with around 6k on them. They came as 7k/6k but I moved the 7k springs to the back and ordered new Tein 12k springs for the front $900 shipped


949 sway bar kit, 1.125" front, 14mm rear with endlinks (which have some surface rust) used the same 6k miles $300 shipped



Mazdaspeed front tri point strut brace $350 shipped


I have some Autoexe underbraces but wont really offer those up until I am going to Chicago in August. I can bring them with me then and ship them via ground.

 

Do you know which part number the sway bar is? They list 3- 1.125 bars for NA and one for NB. Can you post pics of the sway bars or email them to me (sbnova1 at gmail)? Thanks

 

ITB's are sold!

 

ITBs received and everything is as stated. Fast shipping (faster than some of the non-international guys) and good communication. Buy with confidence.

 

PM Sent regarding several items