ALL PARTS are off a 1.8 NA (1997)
Ok so I have some things laying around, need them gone. JUST OFFER, reasonable offers wont be refused!
Located: SoCal, 91754
contact: 714 369 5952
-Joshua

-Toda Oil pump gear Brand New- $250obo
-HKS Hypermax II (under 2k miles)- $1,000obo **PENDING FOR $650 + $200 value part trade
-3" TiAL v-band down pipe (1.2k miles side mount and bottem mount ok)- $150obo PENDING for $100
-Stock exhaust with a tanabe axle back (on car when purchased at 112k miles)- $50obo
-T3/T4 China charger .63ar Brand New!- $175obo shipped *EDITED T28 is gone
"Intake: 3 inch
Inlet: 2 inch
Compressor trim: .50
Compressor Wheel diameter: 50.16 / 76.84
Turbine Wheel diameter: 54.06 / 65.20
Exhaust Trim: .63ar
Turbine flange type : T3 flange
Down pipe flange type: 5 bolt standard
Cooling type: oil cool only
Horsepower rating: 350+"
http://www.ebay.com/itm/GODSPEED-T04...ht_3139wt_1185
-RC550cc New w/pigtails (I can't find flow charts)- $300obo
-Couplings (90, and 45 degree different sizes)- $2.50 ea.
-IC piping (stright pipe 3")- $15
-1.8 NA Intake Mani stock(112k miles, CLEAN)- $90obo

added:
-bunch of claps various sizes- $1 ea.
-52mm gauge pod (mounts on dash/ wheel hub cover/ gauge hood)- $5
-52mm radio delete gauge pod- $10
-1.8 bare stock intake manifold (off an 97 NA8)- $100 obo



Coilovers


RCs



Toda


Stock exhaust


Stock intake mani


SOLD:
China charger T28- $100 SOLD for $100 shipped
Begi turbo heat shield- $80obo SOLD for 73.50 shipped!
AutoMeter Air/Fuel gauge (unknown usage, I never installed it)- $20obo SOLD FOR $35 shipped
3" ARTech v-band Mid pipe (unknown miles, CLEAN with flex pipe, and bundge)- $150obo SOLD FOR $130 SHIPPED
Supertech OverSized Valvetrain (1.2k milescomplete)- $225obo **SOLD FOR $300 shipped
part# RET-TS60/MA2 & SEAT-TS/MA181 (valves)
SPRK-MM18S-K (Springs)
RET-TS60MA2 (Retainers)

 

Am I missing what this stuff is for? NA/NB/1.6/1.8?

 

edited, thank you! haha

 

More specs on the turbo? Picutres/link to info?

 

Also would like pictures/specs on the turbo

 

updated pm'd replied

 

That T28 went fast haha.

 

it was cheap. and I'm open to offers. Just cleaned my in box. Don't rob me though, all parts listed with out a mileage is pretty much new, if not new then just test fitted or I went with DIY.

 

Seriously? God damn you whoever bought it. I will hunt you down and do a burnout on your face.

 

added a Toda oil pump gear, and more pictures Valves pending

 

What is that elbow with v band on the end in the second picture? That for sale separate?

What kit is the heatsheild from?

 

that is the flange, I had the ARTtech DP (but it was damaged from storage so I cut off the flange so it can be attached to the new down pipe)

The heat shield is not from a kit I just bought it.
http://www.bellengineering.net/produ...roducts_id=432

GOING TO THE POST OFFICE NOW!

 

Money sent for heatshield. Sorry again for the delayed response.

 

Can I take the Autometer A/F guage? I can't send you a PM because I have under 15 postcounts :( fml.

 

pming you about midpipe

 

Will you part the pnp clips from the injectors?

 

Call/ text me. That's why I left my number


Ill part it. Text me.

I won't part them at the moment. Sorry.

 

What constitues 'oversize valvetrain'? Looks like +1mm valves, single springs and retainers/ seats?

 

Still have the coilovers and what do you want for them?

 

Interested in the valve train setup! Pm me if still unclaimed..