Miata part out, everything but the turbo
Thread Starter
Senior Member
iTrader: (10)
Joined: Aug 2007
Posts: 1,186
Total Cats: 4
From: Fredericton, NB
Prices do not include shipping what you see below is what is left!
Harddog Hard Bar Sport - Black Powdercoat w/ Double Diagonal ($500)
-M1 Version (Plastic Window only.) Will fit 99+ NB but will be very tight on the glass rear window (NOT RECOMMENDED)
-Comes with backing plates and bolts (Recommended to replace lock washers/bolts on re-installation)
-Stitched Cover w/ Custom Formed High Density Padding, Black Leather
Built 1.8L engine block($2000 for assembled block/head ran for 1 year):
-ARP headstuds
-Belfab Rods, Weisco Pistons
-Street/Strip Boundary Engineering Oil Pump
-new OEM Headgasket, new OEM valve seals,
-Full head dip and planning on assembly @ Central Engine (Local Machine Shop)
-Changed Waterpump and installed Gates Racing Timing belt last fall
-Synthetic Rotella T6 ran since after break in.
-Knock Sensor (NB Active Style)
-TrackSpeed 12-1 Timing wheel with NB Sensor
-Comp Engine Mounts
Coolant Re-Route with Radiator ($400)
-CX Racing Radiator with shrouded fans (modified inlet to match re-route)
-Coolant Spacer & Coolant lines coming from rear of head
-Stock Oil Cooler inlet bypasses thermostat and returns directly to radiator inlet from rear of head
-FJO Peak and Hold injector driver ($130)
-RC 750cc Peak and Hold injectors ($200)
-Flying Miata Stage 2 Pressure Plate, Clutch ($220)
SOLD-FM2 Cast Manifold
SOLD-T28 Internally Gated Ported Chinabob Turbo (comes with extra GT28 Garrett Turbo, I know the Chinese turbo currently on the car won't last so I have this one ready to go)
SOLD-Air to Air intercooler with Flyin Miata 1 Piece Silicone lines on hot and cold side.
SOLD-AEM Standalone EMS tuned to the current 21psi Peak
SOLD-Walboro 255LPH Fuel Pump
SOLD-Toyota Coil on Plug conversion with bracket
SOLD-6speed transmission off 2003 SE ($800)
SOLD-3.9 torsion2 off 2003 SE ($700, does not include diff arms)
SOLD-Flying Miata Dual Feed fuel rail ($200 with lines and stock FPR)
SOLD-Flying Miata Flywheel
SOLD-5speed transmission off a 97 ($150)
SOLD-Urethane "touge run" front lip for NA ($70)
SOLD-NB Style Megan EZ Street suspension ($700)...These are coming off my MSM and have very little mileage on them. Will also fit NA
SOLD-Full Prothane Urethane Bushings everywhere (Will remove control arms in part out $50 per arm with bushings installed)
SOLD - Still has PS and AC ($150 for each, will include MSM PS rack for PS)
SOLD-Harddog racing double rollbar ($400 or will trade for M2 bar to fit the MSM)
SOLD-All body panels are also available along with a very good condition soft top.
SOLD-Have a brand new never installed passenger fender as well
Harddog Hard Bar Sport - Black Powdercoat w/ Double Diagonal ($500)
-M1 Version (Plastic Window only.) Will fit 99+ NB but will be very tight on the glass rear window (NOT RECOMMENDED)
-Comes with backing plates and bolts (Recommended to replace lock washers/bolts on re-installation)
-Stitched Cover w/ Custom Formed High Density Padding, Black Leather
Built 1.8L engine block($2000 for assembled block/head ran for 1 year):
-ARP headstuds
-Belfab Rods, Weisco Pistons
-Street/Strip Boundary Engineering Oil Pump
-new OEM Headgasket, new OEM valve seals,
-Full head dip and planning on assembly @ Central Engine (Local Machine Shop)
-Changed Waterpump and installed Gates Racing Timing belt last fall
-Synthetic Rotella T6 ran since after break in.
-Knock Sensor (NB Active Style)
-TrackSpeed 12-1 Timing wheel with NB Sensor
-Comp Engine Mounts
Coolant Re-Route with Radiator ($400)
-CX Racing Radiator with shrouded fans (modified inlet to match re-route)
-Coolant Spacer & Coolant lines coming from rear of head
-Stock Oil Cooler inlet bypasses thermostat and returns directly to radiator inlet from rear of head
-FJO Peak and Hold injector driver ($130)
-RC 750cc Peak and Hold injectors ($200)
-Flying Miata Stage 2 Pressure Plate, Clutch ($220)
SOLD-FM2 Cast Manifold
SOLD-T28 Internally Gated Ported Chinabob Turbo (comes with extra GT28 Garrett Turbo, I know the Chinese turbo currently on the car won't last so I have this one ready to go)
SOLD-Air to Air intercooler with Flyin Miata 1 Piece Silicone lines on hot and cold side.
SOLD-AEM Standalone EMS tuned to the current 21psi Peak
SOLD-Walboro 255LPH Fuel Pump
SOLD-Toyota Coil on Plug conversion with bracket
SOLD-6speed transmission off 2003 SE ($800)
SOLD-3.9 torsion2 off 2003 SE ($700, does not include diff arms)
SOLD-Flying Miata Dual Feed fuel rail ($200 with lines and stock FPR)
SOLD-Flying Miata Flywheel
SOLD-5speed transmission off a 97 ($150)
SOLD-Urethane "touge run" front lip for NA ($70)
SOLD-NB Style Megan EZ Street suspension ($700)...These are coming off my MSM and have very little mileage on them. Will also fit NA
SOLD-Full Prothane Urethane Bushings everywhere (Will remove control arms in part out $50 per arm with bushings installed)
SOLD - Still has PS and AC ($150 for each, will include MSM PS rack for PS)
SOLD-Harddog racing double rollbar ($400 or will trade for M2 bar to fit the MSM)
SOLD-All body panels are also available along with a very good condition soft top.
SOLD-Have a brand new never installed passenger fender as well
Last edited by Preluding; Aug 3, 2013 at 07:26 AM.
0
Its not going in a,oem application i just need to make sure it will physically bolt up. Can you email me picture icpkorn23@aim.com
0
Thread Starter
Senior Member
iTrader: (10)
Joined: Aug 2007
Posts: 1,186
Total Cats: 4
From: Fredericton, NB
I believe they are regular.... I'm actually not sure what you mean by "extreme drop"
My car was sitting quite low and I had tons of extra left on the coil....hope that helps
My car was sitting quite low and I had tons of extra left on the coil....hope that helps
0
Newb
Joined: Jun 2013
Posts: 2
Total Cats: 0
0
0
